™
COMPREHENSIVE INTERNET SECURITY
SonicWALL Internet Security Appliances
TZ 170 Quick Start Guide
Quick Start Installation
Thank you for purchasing a SonicWALL Internet security appliance. The SonicWALL acts as a secure
barrier between your private LAN and the public Internet (WAN) to protect your networks from security
threats on the Internet.
This Quick Start Guide provides instructions for installing and configuring your SonicWALL TZ 170 as an
Office Gateway on your network. After you complete this guide, you can access the Internet securely
through your LAN connection.
Before You Begin
Check Package Contents
•
•
•
•
•
•
•
One SonicWALL Internet Security Appliance
One SonicWALL Quick Start Guide
One SonicWALL Firmware and Documentation CD
One Ethernet cable
One RJ45 CLI cable*
One 5 Volt DC power supply
One Power cord**
*The RJ45 CLI cable is only included with the purchase of a TZ 170 with SonicOS Enhanced.
**A power cord is included only with units shipped to North America.
If any items are missing from your package, contact SonicWALL, Inc.
Web: <http://www.sonicwall.com/support/> Phone: (888) 777-1476
Overview of the SonicWALL TZ 170 Hardware
Test Light
WAN
Link, 100, Activity
opt
Power Light
LAN
Link, Activity
Link, 100, Activity
LAN Ports 1-5
Optional Port
Power
Console Port
WAN Port
SonicWALL TZ 170 Quick Start Guide Page 1
What You Need to Get Connected
•
•
•
•
SonicWALL Internet Security Appliance
Internet Connection
PC or Macintosh computer
A Web browser (Microsoft Internet Explorer v5.0 or later, or Netscape Navigator v4.7 or later - your
Web browser must support Java and HTTP uploads in order to fully manage the SonicWALL.)
Internet Service Provider (ISP) Information TEL:______________________________
•
ISP Connection Information
Before you can begin installing your SonicWALL, determine how your ISP distributes IP addresses. Call
your ISP to find out if your Internet connection uses DHCP to obtain an IP address, or PPPoE (typical of
DSL access), or if they have given you a static IP address. Record all of your networking information in the
checklist below:
IP Addressing using DHCP
No action necessary. The SonicWALL automatically detects the presence of a DHCP server during setup.
IP Addressing using PPPoE
User Name:________________________
Password:_________________________
IP Addressing using a Single, Static Public IP Address
IP Address:________________________
Subnet Mask:______________________
Default Gateway:___________________
Primary DNS:______________________
Secondary DNS:___________________
If you are not using one of the network configurations above, step by step installation instructions for
additional networking methods are found in Configuring the Network Mode section of your Administrator’s
Guide. The Administrator’s Guide is located on your product CD and requires Acrobat Reader to view it.
Alert!
Acrobat Reader is also provided on your product CD.
Glossary
•
•
IP Address - A set of numbers in the format, XXX.XXX.XXX.XXX, used to address computers on the Internet.
Subnet Mask - A set of numbers in IP address format using 255 in place of the XXX’s. It determines the type of
network by “masking” out numbers. A Class C network has a subnet mask of 255.255.255.0.
Default Gateway - A device on an internetwork that forwards packets to another network.
DNS (Domain Name System) Server - A computer that “looks up” the name of a computer and finds the
corresponding IP address. This allows you to access computers on the Internet without configuring IP addresses
for remote connections.
•
•
•
•
•
PPPoE - Point to Point Protocol over Ethernet supports the transmission of network packets over serial transmis-
sion lines such as DSL or POTS (Plain Old Telephone Service).
DHCP - Dynamic Host Configuration Protocol allocates IP addresses to computers on the network automatically
without assigning a computer a static (fixed) IP address.
VPN - Virtual Private Network is a “virtual” network that encrypts data and sends it privately over the Public
Internet
Setup Continues
Page 2
Setting Up Your SonicWALL
Applying Power to the SonicWALL
Attach the power supply to the power cord. Plug the power adapter into the SonicWALL and plug
the other end into a power outlet.
1
The Power light turns green when power is applied to the SonicWALL. Also, the Test light remains
lit for approximately 90 seconds while the SonicWALL performs a series of diagnostic tests.
Connecting the SonicWALL to the Network
Connect one end of an Ethernet cable to your DSL modem, cable modem, or Internet router.
2
Connect the other end of the Ethernet cable to the WAN port of the SonicWALL. The link LED
lights indicating an active connection. .
Connect one end of an Ethernet cable to the Ethernet port of your computer.
3
Connect the other end of the cable to LAN 1 port of your SonicWALL. The link LED lights
indicating an active connection.
Setup Continues
SonicWALL TZ 170 Quick Start Guide Page 3
4
Configuring Your Management Station
Your SonicWALL is configured with the default IP address of 192.168.168.168. This IP address is used to
initially access the Management interface of the SonicWALL and launch the Setup Wizard. To access the
Management interface for the first time, you must configure your computer with an IP address in the same
network range as the SonicWALL. Follow the instructions below for your operating system:
Windows XP
1. Click Start, then Connect to.
2. Right-click on the Local Area Connection icon and select Properties.
3. Open the Local Area Connection Properties window.
4. Double-click Internet Protocol (TCP/IP) to open the Internet Protocol (TCP/IP) Properties window.
5. Select Use the following IP address and type 192.168.168.200 in the IP address field.
6. Type 255.255.255.0 in the Subnet Mask field.
7. Type the DNS IP address in the Preferred DNS Server field. If you have more than one address, type the second
one in the Alternate DNS server field.
8. Click OK for the settings to take effect on the computer.
Windows 2000
1. From your Windows task bar, click Start.
2. Then click Settings.
3. Click Network and Dial-up Connections.
4. Double-click the network icon to open the connection window.
5. Click Properties.
6. Highlight Internet Protocol (TCP/IP) and click Properties.
7. Select Use the following IP address.
8. Enter 192.168.168.200 in the IP address field.
9. Enter 255.255.255.0 in the Subnet field.
10. If you have a DNS Server IP address from your ISP, enter it in the Preferred DNS Server field.
Windows NT
1. From the Start list, highlight Settings and then select Control Panel.
2. Double-click the Network icon in the Control Panel window.
3. Double-click TCP/IP in the TCP/IP Properties window.
4. Select Specify an IP Address.
5. Type "192.168.168.200" in the IP Address field.
6. Type "255.255.255.0" in the Subnet Mask field.
7. Click DNS at the top of the window.
8. Type the DNS IP address in the Preferred DNS Server field. If you have more than one address, enter the
second one in the Alternate DNS server field.
9. Click OK, and then click OK again.
10. Restart the computer.
Setup Continues
Page 4
Windows 98
1. From the Start list, highlight Settings and then select Control Panel. Double-click the Network icon in the Control
Panel window.
2. Double-click TCP/IP in the TCP/IP Properties window.
3. Select Specify an IP Address.
4. Type "192.168.168.200" in the IP Address field.
5. Type "255.255.255.0" in the Subnet Mask field.
6. Click DNS Configuration.
7. Type the DNS IP address in the Preferred DNS Server field. If you have more than one address, type the second
one in the Alternate DNS server field.
8. Click OK, and then click OK again.
9. Restart the computer for changes to take effect.
Launching the Setup Wizard
To begin the configuration of your SonicWALL, you must log into the SonicWALL using a Web
5
browser and the default LAN IP address, 192.168.168.168, of the SonicWALL. Follow the
instructions below:
1. Launch your Web browser.
Because you are temporarily disconnected from the Internet, you may receive an error message when your
Web browser first opens. This does not affect your installation process. Continue with the steps below.
Alert!
2. Enter 192.168.168.168 in the Location or Address field.
Your Web browser must support Java and HTTP uploads in order to fully manage the SonicWALL appliance.
Internet Explorer 5.0 or higher, as well as Netscape Navigator 4.0 or higher, are recommended.
Alert!
3. The SonicWALL Installation Wizard launches and guides you through the configuration and
setup of your SonicWALL.
Setup Continues
SonicWALL TZ 170 Quick Start Guide Page 5
If you cannot connect to the SonicWALL TZ 170, check the following:
•
•
•
Did you correctly enter the SonicWALL TZ 170 LAN IP address in your browser window?
Is the SonicWALL TZ 170 connected to the same network as your computer?
Have you changed the TCP/IP network settings on your computer? (Step 4)
The Setup Wizard
6
The Setup Wizard provides easy to follow instructions for configuring the SonicWALL on your
network. You must have your ISP information to complete the configuration using the Setup
Wizard.
Certain browser configurations may not launch the Installation Wizard automatically. In this case,
TIP!
you must log into the SonicWALL using “Admin” as the User Name and “password” as the
Password. After you log into the SonicWALL, click Wizards. Select Setup to begin configuring the
SonicWALL.
Follow the steps below for the quickest and easiest configuration for the TZ 170 as an Office
Gateway:
Step 1: Welcome - Read the information on the Welcome dialogue box. Click Next.
Step 2: Change Password - change the TZ 170 password to your personal password. Click
Next.
Step 3: Change Time Zone - change the Time Zone to your location’s Time Zone. Click Next.
Step 4: WAN Network Mode - the type of network connectivity is detected automatically. If you
want to select a different network mode, consult the SonicOS 2.0s Administrator’s Guide on your
product CD for more information.
Step 5: WAN Network Mode - if PPPoE is detected as your network connection, enter your user
name and password from your ISP. Click Next. If a DHCP server is detected, click Next.
Step 6: LAN Settings - Review the LAN IP address and subnet mask. Use the default values.
Step 11: SonicWALL Configuration Summary - Write down your network configuration
information below. Click Apply.
Setup Wizard Complete - Your SonicWALL is now successfully configured for LAN and Internet
access. Click Restart to complete the configuration process.
Network Settings
WAN - Network Mode:______________ IP Address:____________ Subnet Mask:____________
Router IP Address:_______________ DNS Server 1 IP Address:______________
DNS Server 2 IP Address:_________________
LAN - IP Address:______________ Subnet Mask:______________DHCP Enabled: Yes___ No__
SonicWALL SonicOS 2.0s firmware and access technical support.
TIP!
Setup Continues
Page 6
Configuring Computers on the LAN
When the SonicWALL restarts, a window displays information to configure computers on your LAN.
7
DHCP Server Enabled on the SonicWALL TZ 170
If you enabled the SonicWALL DHCP Server or have a DHCP Server on your LAN, each computer
must be configured to obtain its IP address dynamically. After the SonicWALL has restarted,
change the network settings on the computers on the LAN. Follow the steps below for your
operating system:
Windows XP
1. Click Start, then Connect to.
2. Right-click on the Local Area Connection icon and select Properties.
3. Open the Local Area Connection Properties window.
4. Double-click Internet Protocol (TCP/IP) to open the Internet Protocol (TCP/IP) Properties window.
5. Select Obtain an IP address automatically.
6. Select Obtain DNS Server automatically.
7. Click OK and then OK again for the settings to take effect on the computer.
Windows 2000
1. From your Windows task bar, click Start.
2. Then click Settings.
3. Click Network and Dial-up Connections.
4. Double-click the network icon to open the connection window.
5. Click Properties.
6. Highlight Internet Protocol (TCP/IP) and click Properties.
7. Select Obtain an IP address automatically.
8. Select Obtain DNS Server automatically.
9. Click OK and then OK again for the settings to take effect on the computer.
Windows NT
1. From the Start list, highlight Settings and then select Control Panel.
2. Double-click the Network icon in the Control Panel window.
3. Double-click TCP/IP in the TCP/IP Properties window.
4. Select Obtain an IP address automatically.
5. Click DNS at the top of the window.
6. Select Obtain DNS Server automatically.
7. Click OK, and then click OK again.
8. Restart the computer.
Setup Continues
SonicWALL TZ 170 Quick Start Guide Page 7
Windows 98
1. From the Start list, highlight Settings and then select Control Panel. Double-click the Network icon in the Control
Panel window.
2. Double-click TCP/IP in the TCP/IP Properties window.
3. Select Obtain IP Address automatically.
4. Click DNS Configuration.
5. Select Obtain DNS Server automatically.
6. Click OK, and then click OK again.
7. Restart the computer for changes to take effect.
LAN Configuration Complete!
The SonicWALL is now functioning and protecting your network from Internet-based attacks and break-ins.
DHCP Server Disabled
If you did not enable the SonicWALL DHCP server or you do not have a DHCP server on your network,
you must configure each computer with a static IP address from your LAN IP address range.
After the SonicWALL has restarted, change the nework settings on computers located on the LAN.
Follow the steps below to configure computers on your LAN:
Windows XP
1. Click Start, then Connect to.
2. Right-click on the Local Area Connection icon and select Properties.
3. Open the Local Area Connection Properties window.
4. Double-click Internet Protocol (TCP/IP) to open the Internet Protocol (TCP/IP) Properties window.
5. Select Use the following IP address and type an IP address from your LAN IP range in the IP address field.
6. Type 255.255.255.0 in the Subnet Mask field.
7. Type the SonicWALL LAN IP Address into the Default Gateway field.
8. Type the DNS IP address in the Preferred DNS Server field. If you have more than one address, type the second
one in the Alternate DNS server field.
9. Click OK for the settings to take effect on the computer.
Windows 2000
1. From your Windows task bar, click Start.
2. Then click Settings.
3. Click Network and Dial-up Connections.
4. Double-click the network icon to open the connection window.
5. Click Properties.
6. Highlight Internet Protocol (TCP/IP) and click Properties.
7. Select Use the following IP address.
8. Type an IP address from your LAN IP range IP address field.
9. Enter 255.255.255.0 in the Subnet field.
10. Type the SonicWALL LAN IP Address into the Default Gateway field.
11. If you have a DNS Server IP address from your ISP, enter it in the Preferred DNS Server field.
Page 8
Windows NT
1. From the Start list, highlight Settings and then select Control Panel.
2. Double-click the Network icon in the Control Panel window.
3. Double-click TCP/IP in the TCP/IP Properties window.
4. Select Specify an IP Address.
5. Type an IP address from your LAN IP range in the IP Address field.
6. Type 255.255.255.0 in the Subnet Mask field.
7. Type the SonicWALL LAN IP Address in the Default Gateway field.
8. Click DNS at the top of the window.
9. Type the DNS IP address in the Preferred DNS Server field. If you have more than one address, enter the
second one in the Alternate DNS server field.
10. Click OK, and then click OK again.
11. Restart the computer.
Windows 98
1. From the Start list, highlight Settings and then select Control Panel. Double-click the Network icon in the Control
Panel window.
2. Double-click TCP/IP in the TCP/IP Properties window.
3. Select Specify an IP Address.
4. Type an IP address from your LAN IP range in the IP Address field.
5. Type "255.255.255.0" in the Subnet Mask field.
6. Type the SonicWALL LAN IP Address in the Default Gateway field.
7. Click DNS Configuration.
8. Type the DNS IP address in the Preferred DNS Server field. If you have more than one address, type the second
one in the Alternate DNS server field.
9. Click OK, and then click OK again.
10. Restart the computer for changes to take effect.
LAN Configuration Complete!
The SonicWALL is now functioning and protecting your network from Internet-based attacks and break-ins.
SonicWALL TZ 170 Quick Start Guide Page 9
SonicWALL TZ 170 Technical Specifications
Processor: SonicWALL Security Processor
Dimensions: 9.07 x 6.63 x 1.63 inches
(23.03 x 16.84 x 4.14 cm)
RAM: 64 MB
Weight: 1.15 lb. (0.52 kg)
Flash Memory: 8 MB
Interfaces: 7 10/100 auto-sensing Ethernet
(1) WAN 10/100 Base-T
LEDs:
Status (Power, Test)
(1) Optional Port
(1) 5-port Auto-MDIX Switch
(1) RJ45 Console Port
LAN 1 per port (multifunctional)
WAN (link, activity, 100)
Optional Port (link, activity, 100)
Firewall Performance:90 Mbps
Site to Site VPN Policies:
10 Node - 1
Input Power: 100V to 240VAC
Power Consumption: 12 Watts Maximum
25 Node - 10
Unrestricted Nodes- 10
Bundled VPN Client Sessions:
10 Node - 0
25 Node - 1
Standards: NAT, DNS, RIPv1/v2, TCP/IP, UDP,
ICMP, HTTP, HTTPS, IPSec, ISAKMP/IKE, SNMP,
DHCP, PPPoE, L2TP, PPTP, RADIUS
Unrestricted Nodes- 1
Firewall Nodes: 10/25/Unrestricted
Environment:
o
o
Temperatures 40 - 105 F, (5-40 C)
Relative Humidity 10-90% noncondensing
Concurrent Connections: 6,000
Operational Altitude: 0 to 13,123 ft. (4000m)
VPN Performance: 25+ Mbps (3DES and AES)
Operating System: SonicOS Standard
upgradeable to SonicOS Enhanced
Major Regulatory Compliance:
EMC: FCC Class B, ICES Class B, CE, C-tick,
VCCI, BSMI, MIC
Safety: UL, cUL, TUV/GS, CB, NOM
Page 10
Appendix
Resetting the Firmware to Factory Default Settings
At times, it may be necessary to reset the firmware on your SonicWALL TZ 170. For example, if
you’ve forgotten your password and cannot access the management interface, resetting the
firmware allows you to reset the SonicWALL TZ 170 to factory default settings including the user
name and password.
To quickly reset the firmware to factory default settings, locate the Reset button on the back of
the SonicWALL TZ 170 next to the LAN connection. Using a pointed object, press and hold the
Reset button for 5-10 seconds. All settings are returned to the factory default settings including
the password and the default LAN IP address of 192.168.168.168.
Note: This reset method does not require reloading the firmware.
Resetting Firmware if Firmware is Corrupted (Test Light remains on)
If the Test light remains on after 90 seconds, the firmware may be corrupted. Follow these steps
to load firmware onto the appliance:
1. To load new firmware onto the SonicWALL TZ 170, power down the appliance.
2. Wait 30 seconds, press and hold the Reset button.
3. At the same time, power on the appliance.
4. Continue to hold the Reset button until the Test light begins blinking.
5. Once the Test light stops blinking and remains lit, release the Reset button.
6. Open a Web browser, and type 192.168.168.168 into the Address or Location field.
7. A Web page displays the message, “Firmware appears to be corrupted.” Click Browse to open a File
Open dialogue box. Browse to the location of the firmware file. A rescue version of the firmware is
located on the product CD.
account. Download the latest version of the firmware and then upload it to your appliance.
SonicWALL TZ 170 Quick Start Guide Page 11
|