4-139-513-11(1)
CD/DVD
Player
Operating Instructions
DVP-NS718H
DVP-NS728H
© 2009 Sony Corporation
Lightning
For added protection for this set
during a lightning storm, or when it
is left unattended and unused for
long periods of time, unplug it
from the wall outlet. This will
prevent damage to the set due to
lightning and power-line surges.
Notes about the discs
• To keep the disc clean, handle
the disc by its edge. Do not touch
the surface. Dust, fingerprints, or
scratches on the disc may cause
it to malfunction.
• Do not expose the disc to direct
sunlight or heat sources such as
hot air ducts, or leave it in a car
parked in direct sunlight as the
temperature may rise
considerably inside the car.
• After playing, store the disc in its
case.
• Clean the disc with a cleaning
cloth.
Wipe the disc from the centre
out.
• Do not use solvents such as
benzine, thinner, commercially
available cleaners, or anti-static
spray intended for vinyl LPs.
• If you have printed the disc’s
label, dry the label before
playing.
• Do not use the following discs:
– A disc that has a non-standard
shape (e.g., card, heart).
– A disc with a label or sticker
on it.
– A disc that has cellophane tape
or sticker adhesive on it.
3
On adjusting volume
About this manual
Do not turn up the volume while
listening to a section with very low
level inputs or no audio signals. If
you do, the speakers may be
damaged when a peak level section
is played.
• The instructions in this manual
are for 2 models: DVP-NS718H
and DVP-NS728H. Check your
model name by looking at the
rear panel of the player. DVP-
NS728H is the model used for
instruction purposes. Any
Precautions
On safety
Should any solid object or liquid
fall into the cabinet, unplug the
player and have it checked by
qualified personnel before
operating it any further.
On cleaning
difference in operation is clearly
indicated in the text, for
example, “DVP-NS728H only.”
Clean the cabinet, panel, and
controls with a soft cloth slightly
moistened with a mild detergent
solution. Do not use any type of
abrasive pad, scouring powder or
solvent such as alcohol or benzine.
• Icons, such as
, listed at
On power sources
the top of each explanation
indicate what kind of media can
be used with the function being
explained.
For details see “Playable Media”
• Instructions in this manual
describe the controls on the
remote. You can also use the
controls on the player if they
have the same or similar names
as those on the remote.
• “DVD” may be used as a general
term for commercial DVDs,
DVD+RWs/DVD+Rs/DVD+R
DLs (+VR mode) and DVD-
RWs/DVD-Rs/DVD-RDLs(VR
mode, video mode).
• The player is not disconnected
from the AC power source
(mains) as long as it is connected
to the wall outlet, even if the
player itself has been turned off.
• If you are not going to use the
player for a long time, be sure to
disconnect the player from the
wall outlet. To disconnect the
AC power cord (mains lead),
grasp the plug itself; never pull
the cord.
On cleaning discs, disc/lens
cleaners
Do not use cleaning discs or disc/
lens cleaners (including wet or
spray types). These may cause the
apparatus to malfunction.
On replacement of parts
In the event that this unit is
repaired, repaired parts may be
collected for reuse or recycling
purposes.
On placement
• Place the player in a location
with adequate ventilation to
prevent heat build-up in the
player.
• Do not place the player on a soft
surface such as a rug.
• Do not place the player in a
location near heat sources, or in a
place subject to direct sunlight,
excessive dust, or mechanical
shock.
• Do not install this player in a
confined space, such as a
bookshelf or similar unit.
• Install the player so that the AC
power cord (mains lead) can be
unplugged from the wall socket
immediately in the event of
trouble.
• If the player is brought directly
from a cold to a warm location,
or is placed in a very damp room,
moisture may condense on the
lenses inside the player. Should
this occur, the player may not
operate properly. In this case,
remove the disc and leave the
player turned on for about half an
hour until the moisture
Copyrights
• This product incorporates
copyright protection technology
that is protected by U.S. patents
and other intellectual property
rights. Use of this copyright
protection technology must be
authorized by Macrovision, and
is intended for home and other
limited viewing uses only unless
otherwise authorized by
• NEED-to-know information (to
prevent incorrect operation) is
listed under the b icon. NICE-
to-know information (tips and
other useful information) is
listed under the z icon.
IMPORTANT NOTICE
Caution: This player is capable
of holding a still video image or
on-screen display image on your
television screen indefinitely. If
you leave the still video image or
on-screen display image
Macrovision. Reverse
engineering or disassembly is
prohibited.
• “DVD+RW,” “DVD-RW,”
“DVD+R,” “DVD+R DL,”
“DVD-R,” “DVD VIDEO,” and
“CD” logos are trademarks.
• This DVD player incorporates
High-Definition Multimedia
Interface (HDMI™) technology.
HDMI, the HDMI Logo and
High-Definition Multimedia
Interface are trademarks or
registered trademarks of HDMI
Licensing LLC.
displayed on your TV for an
extended period of time you risk
permanent damage to your
television screen. Plasma display
panel televisions and projection
televisions are susceptible to
this.
If you have any questions or
problems concerning your player,
please consult your nearest Sony
dealer.
evaporates.
• When you move the player, take
out any discs. If you don’t, the
disc may be damaged.
4
Table of Contents
Step 1: Connecting to Your TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
About the CONTROL FOR HDMI functions for ‘BRAVIA Sync’
(for HDMI connections only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Step 5: Quick Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
‘BRAVIA Sync’ display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Various Play Mode Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Adjusting the playback picture (CUSTOM PICTURE MODE) . . . . . . . . . 28
Playing video, photo, and music files from USB device
(DVP-NS728H only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
SCREEN SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
CUSTOM SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Setting the digital output signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
HDMI SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
,continued
5
Self-diagnosis Function (When letters/numbers appear on the screen) . . . . 44
Playable Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Parental Control Area Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
6
Guide to Parts and Controls
For more information, see the pages indicated in parentheses.
Remote
Turns on the player, or sets to standby
mode.
TV
TV
PICTURE
NAVI
Adjusts the TV volume.
TIME/TEXT
B Number buttons
CLEAR
AUDIO SUBTITLE
MENU
Enters the title/chapter numbers, etc.
TOP MENU
CLEAR (22)
Clears the entry field.
RETURN
DISPLAY
Displays the playing time and
remaining time on the TV screen or
front panel display. Press repeatedly
to change the displayed information.
CD/DVD text appears only when text
is recorded on the disc.
FAST/SLOW
PLAY
If music file has an ID3 tag, the player
will display the album name/track title
from the ID3 tag information. This
player supports ID3 versions 1.0/1.1
and 2.2/2.3.
2 (volume) +, number 5, AUDIO, and N
buttons have a tactile dot. Use the tactile dot
as a reference when operating the player.
AUDIO (
)
Changes the audio language or audio
channel.
Divides the screen into 9 subscreens
so you can choose the desired scene
quickly.
When 4 digits are displayed, they
indicate a language code. See
see which language the code
represents.
Each time you press the button, the
display changes as follows:
• CHAPTER VIEWER
– Changes the subtitles when
subtitles are recorded on DVD
VIDEOs/DVD-VR mode/DivX
video files only.
• TITLE VIEWER
• TRACK VIEWER
The photo files in the album appear in
16 subscreens.
– Displays lyrics for a music file
when pressed during playback. For
Switches between TV and other input
sources.
Turns on the TV, or sets to standby
mode.
,continued
7
D TOP MENU
Displays the DVD’s top menu.
FAST/SLOW PLAY
*6
Plays in various speed with sound
when pressed repeatedly during
playback.
Displays the menu.
1
*
For DivX video files and DVDs except
DVD+RWs/DVD+Rs/DVD+R DLs.
For DVDs and DivX video files only.
These functions may not work with some
scenes.
For DVD VIDEOs and DVD-VR mode only.
For DVDs, VIDEO CDs, and video files only.
For DVDs and VIDEO CDs only.
Returns to the previous display.
2
3
*
*
DISPLAY (21)
Displays the playback information on
the screen.
4
5
6
*
*
*
Moves the highlight to select a
b
Some playback functions may not work with
displayed item.
Enters the selected item.
E ./> (previous/next)
Skips to the previous/next chapter,
track, or scene in continuous play
mode.
/
(replay/step/step/
advance)
– Replays the scene
forward the scene
*1*3
/briefly fast
*2*3
when pressed
during playback.
*4
*5
– Plays backward /forward one
frame at a time when pressed during
pause mode.
– Changes the LUN (Logical Unit
Number) devices when pressed
during the list of albums or tracks is
m/M
(scan/slow)
– Fast reverses/fast forwards when
pressed during playback. The speed
changes when pressed repeatedly.
*4
*5
– Plays backward /forward in
slow motion when pressed
repeatedly during pause mode.
N (play)
Starts or re-starts playback.
X (pause)
Pauses or re-start playback.
x (stop)
Stops playback.
8
Front panel
To lock the disc tray (Child Lock)
You can lock the disc tray to prevent it being
opened by mistake.
When the player is in standby mode, press
O RETURN, ENTER, and then [/1 on the
remote.
Opens or closes the disc tray.
The N button has a tactile dot*.
The player turns on and “LOCKED” appears
on the front panel display. The Z button on
the player does not work while the Child
Lock is set.
Stops playback.
G
(DVP-NS728H only)
To unlock the disc tray
When the player is in standby mode, press
O RETURN, ENTER, and then [/1 again.
Connect a USB device to this jack.
H
b
* Use the tactile dot as a reference when operating
the player.
Even if you select “RESET” under “SETUP” in the
locked.
Rear panel
A HDMI OUT (High-Definition
F COMPONENT VIDEO OUT jacks
(11)
,continued
9
Front panel display
A N, X
When playing music or video files
Current file or track playing
*1
*2
Lights up during playback or pause.
time and number
B
r
Lights up during Repeat Play.
*1
Current file or track name/MP3
C
*2
ID3 track title
Lights up when you can change the
angle.
r
*1
Current album and file or
*2
track number
D Playback information
(Returns to top automatically)
You can view the time and text
information by pressing the TIME/
TEXT button on the remote repeatedly.
The display changes as follows:
1
* for video file
2
* for music file
When playing a VIDEO CD (without
When playing a DVD
PBC functions) or CD
Current title playing time
Current track playing time and
number
r
Current title remaining time
r
r
Current track remaining time
Current chapter playing time
r
r
Disc playing time
Current chapter remaining time
r
r
Text
r
Disc remaining time
r
Text
Current title and chapter number
(Returns to top automatically)
10
Hookups and Settings
When unpacking, check the supplied accessories by referring to page 47.
b
• Plug cords securely to prevent unwanted noise.
• Refer to the operating instructions supplied with the components to be connected.
• Be sure to disconnect the mains lead of each component before connecting.
Step 1: Connecting to Your TV
Connect this player to your TV using a video cord. Select one of the patterns A through D,
according to the input jack on your TV.
In order to view progressive signal (525p or 625p) pictures with a compatible TV, you must use
pattern C. Select pattern B when connecting to a TV equipped with HDMI input.
INPUT
INPUT
(yellow)
A
Audio/video
cord (not supplied)
VIDEO
D
(white)
TV
L
AUDIO
(red)
R
SCART cord
(not supplied)
TV
(yellow)
to LINE (RGB)-TV
to LINE OUT (VIDEO)
to HDMI OUT
CD/DVD player
(green)
(blue)
(red)
HDMI cord
(not supplied)
to COMPONENT
VIDEO OUT
COMPONENT
VIDEO IN
Y
B
(green)
(blue)
(red)
PB/CB
HDMI IN
P
R/CR
TV
Component video
cord (not supplied)
TV
C
: Signal flow
,continued
11
b
To connect to a TV with DVI input
Use an HDMI-DVI converter cord (not
supplied). The DVI jack will not accept any
audio signals, so you have to use another
audio connection in addition to this
cannot connect the HDMI OUT jack to DVI
jacks that are not HDCP compliant (e.g., DVI
jacks on PC displays).
When connecting to a progressive TV, it is
recommended that you use only pattern C. If you
connect to your TV using both C and D, a special
control signal transmitted via the SCART cord may
cause the signal to be switched to the SCART jack.
A Video input jack
You will enjoy standard quality images.
B HDMI/DVI input jack
Use a certified Sony HDMI cord to enjoy
high quality digital picture and sound through
the HDMI OUT jack.
C Component video input jacks
(Y, PB/CB, PR/CR
)
You will enjoy accurate colour reproduction
and high quality images.
When connecting to a Sony TV that is
compatible with the CONTROL FOR HDMI
D SCART input jack
Be sure to make the connections firmly to
avoid hum and noise. When you connect
using the SCART cord, check that the TV
conforms to RGB signals. Refer to the
operating instructions supplied with the TV to
be connected. Also, when you set “LINE” to
“RGB (COMPONENT OFF)” under
“SCREEN SETUP” in the Setup Display
(page 35), use a SCART cord that conforms
to each signal.
When connecting to the HDMI OUT jack
Follow the steps below. Improper handling
may damage the HDMI OUT jack and
the connector.
1 Carefully align the HDMI OUT jack on
the back of the player and the HDMI
connector by checking their shapes.
Make sure the connector is not upside
down or tilted.
When connecting to a standard 4:3 screen
TV
Some images may not fit your TV screen. To
b
• Do not connect more than one type of video cord
between the player and your TV at the same time.
• Do not use connections B and D at the same
time.
Not straight
Connector is upside
down
• Do not connect a VCR, etc., between your TV and
the player. If you pass the player signals via the
VCR, you may not receive a clear image on the
TV screen. If your TV has only one audio/video
input jack, connect the player to this jack.
2 Insert the HDMI connector straight into
the HDMI OUT jack.
Do not bend or apply force to the HDMI
connector.
12
• When you connect the player to your TV via the
SCART jack, the TV’s input source is set to the
player automatically when you start playback. In
this case, press TV t (input select) on the
remote to return the input to the TV.
• If you set “LINE” in “SCREEN SETUP” to
player outputs no component video signals.
• Be sure to disconnect the HDMI cord when
moving the player.
• Do not apply too much pressure to the cabinet
wall, if you place the player on the cabinet with
the HDMI cord connected. It may damage the
HDMI OUT jack or the HDMI cord.
• When connecting or disconnecting, do not screw
in or rotate the HDMI connector.
When you play a disc recorded in the NTSC
colour system, the player outputs the video
signal or the Setup Display etc. in the NTSC
colour system and the picture may not
appear on the PAL colour system
televisions. In this case, open the tray and
remove the disc.
About the CONTROL FOR HDMI
functions for ‘BRAVIA Sync’
(for HDMI connections only)
By connecting to Sony components that are
compatible with the CONTROL FOR HDMI
function with an HDMI cord (not supplied),
you can enjoy the following features:
• One-Touch Play (page 19)
• System-Power Off
When you turn the TV off by using the [/1 button
on the TV’s remote, the components compatible
with CONTROL FOR HDMI function turn off
automatically.
b
Depending on the connected component, the
CONTROL FOR HDMI function may not work.
Refer to the operating instructions supplied with the
component.
13
Step 2: Connecting to Your Audio Component
Select one of the following patterns A or B, according to the input jack on your TV monitor,
projector, or audio component such as an AV amplifier (receiver).
This will enable you to listen to sound.
INPUT
VIDEO
(yellow)*
(red)
Audio/video cord
(not supplied)
A
(white)
(red)
(white)
L
AUDIO
(yellow)*
R
TV, projector, or
audio component
to LINE OUT L/R (AUDIO)
CD/DVD player
to DIGITAL OUT (COAXIAL)/HDMI OUT
or
Coaxial digital cord
(not supplied)
HDMI cord (not supplied)
to coaxial/HDMI
digital input
B
[Speakers]
Rear (L)
[Speakers]
Rear (R)
Front (R)
Front (L)
Audio component
with a decoder
Subwoofer
Centre
: Signal flow
z
For correct speaker location, see the operating instructions supplied with the connected components.
14
A Audio L/R input jacks
This connection will use your TV’s or audio
component’s two speakers for sound.
Step 3: Connecting the
Mains Lead
B Digital audio input jack
Plug the player and TV mains lead (power
cord) into a mains.
1
If your audio component has a Dolby*
2
Digital, DTS* , or MPEG audio decoder and
a digital input jack, use this connection. You
can enjoy Dolby Digital (5.1ch), DTS
(5.1ch), and MPEG audio (5.1ch) surround
effect.
If you connect to a Sony audio component
that is compatible with the CONTROL FOR
HDMI function, refer to the operating
instructions supplied with the audio
component.
Step 4: Preparing the
Remote
Insert two R6 (size AA) batteries by matching
the 3 and # ends on the batteries to the
markings inside the compartment. When
using the remote, point it at the remote sensor
on the player.
*1
Manufactured under license from Dolby
Laboratories.
Dolby, Pro Logic, and the double-D symbol are
trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent #:
*2
5,451,942 & other U.S. and worldwide patents
issued & pending. DTS and DTS Digital Out are
registered trademarks and the DTS logos and
Symbol are trademarks of DTS, Inc. © 1996-
2008 DTS, Inc. All Rights Reserved.
b
b
• After you have completed the connection, make
If your audio component has an MPEG audio
decoder function, set “MPEG” to “MPEG” in
sound or a loud noise will come from your
speakers.
• The TVS effects of this player cannot be used
with this connection.
• When you connect the player to an audio
component using an HDMI cord, you will need to
do one of the following:
• Do not leave the remote in an extremely hot or
humid place.
• Do not drop any foreign object into the remote
casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light
from the sun or a lighting apparatus. Doing so
may cause a malfunction.
• If you do not use the remote for an extended
period of time, remove the batteries to avoid
possible damage from battery leakage and
corrosion.
– Connect the audio component to the TV with the
HDMI cord.
– Connect the player to the TV with a video cord
other than HDMI cord (component video cord or
audio/video cord).
• When connecting to the HDMI OUT jack,
carefully align the HDMI connector with the jack.
Do not bend and apply force to the HDMI cord.
,continued
15
Controlling TVs with the remote
You can control the sound level, input source,
and power switch of your Sony TV with the
supplied remote.
Step 5: Quick Setup
Follow the steps below to make the minimum
number of basic adjustments for using the
player.
To skip an adjustment, press >. To return
to the previous adjustment, press ..
Available buttons
Depending on the connected unit, you may
not be able to control your TV using all or
some of the buttons on the supplied remote.
1
2
Turn on the TV then press [/1.
Buttons
Operations
TV [/1
Turn the TV on or off
Switch the input selector on your
TV so that the signal from the
player appears on your TV screen.
2 (volume)
+/–
Adjust the volume of the
TV
TV t
(input select)
Switch the TV’s input
source between the TV and
other input sources
“Press [ENTER] to run QUICK SETUP”
appears at the bottom of the screen. If this
message does not appear, select
“QUICK” under “SETUP” in the Control
To control other TVs with the remote
You can control the volume, input source, and
power switch of non-Sony TVs as well.
If your TV is listed in the table below, set the
appropriate manufacturer’s code.
3
Press ENTER without inserting a
disc.
The Language Setup Display appears.
b
When you replace the batteries of the remote, the
code number may be reset to the default setting. Set
the appropriate code number again.
LANGUAGE SETUP
OSD:
ENGLISH
MENU:
AUDIO:
SUBTITLE:
ENGLISH
FRANÇAIS
DEUTSCH
ITALIANO
1
While holding down TV [/1, press the
number buttons to select your TV’s
manufacturer’s code.
ESPAÑOL
NEDERLANDS
DANSK
SVENSKA
2
Release TV [/1.
Code numbers of controllable TVs
If more than one code number is listed, try
entering them one at a time until you find the
one that works with your TV.
4
5
Press X/x to select a language.
The player displays the menu and
subtitles in the selected language.
Press ENTER.
The Screen Setup Display appears.
Manufacturer Code number
Sony
01 (default)
Hitachi
JVC
24
SCREEN SETUP
16:9
16:9
4:3 LETTER BOX
4:3 PAN SCAN
TV TYPE:
33
SCREEN SAVER:
BACKGROUND:
LINE:
PROGRESSIVE (COMPONENT OUT ONLY): OFF
MODE (PROGRESSIVE):
4:3 OUTPUT:
LG/Goldstar
Panasonic
Philips
76
17, 49
06, 08, 72
71
AUTO
FULL
Samsung
Sharp
29
Toshiba
38
16
Select “YES: LINE OUTPUT L/R
(AUDIO),” if you connect an audio
component using an audio cord, then go
to step 14.
Select “YES: DIGITAL OUTPUT,” if
you connect an audio component using a
digital coaxial cord/HDMI cord.
6
7
Press X/xto select the setting that
matches your TV type.
◆ If you have a wide-screen TV or a 4:3
standard TV with a wide-screen mode
◆ If you have a 4:3 standard TV
• 4:3 LETTER BOX or 4:3 PAN SCAN
11Press X/x to select the type of
Dolby Digital signal to your audio
component.
Press ENTER.
The Setup Display for selecting the type
of video signal output from the LINE
(RGB)-TV jack appears.
If your audio component has a Dolby
Digital decoder, select “DOLBY
DIGITAL.” Otherwise, select “D-PCM.”
SCREEN SETUP
AUDIO SETUP
TV TYPE:
16:9
ON
AUDIO DRC:
DOWNMIX:
DIGITAL OUT:
DOLBY DIGITAL:
MPEG:
STANDARD
DOLBY SURROUND
ON
SCREEN SAVER:
BACKGROUND:
LINE:
PROGRESSIVE (COMPONE
MODE (PROGRESSIVE):
4:3 OUTPUT:
JACKET PICTURE
VIDEO
VIDEO
RGB (COMPONENT OFF)
FULL
DOLBY DIGITAL
DOLBY DIGITAL
D-PCM
DTS:
48kHz/96kHz PCM:
48kHz/16bit
8
9
Press X/x to select the type of
signal you want to output from the
LINE (RGB)-TV jack.
12Press ENTER.
“DTS” is selected.
AUDIO SETUP
AUDIO DRC:
DOWNMIX:
DIGITAL OUT:
DOLBY DIGITAL:
MPEG:
STANDARD
◆ Video signals
• VIDEO (page 35)
DOLBY SURROUND
ON
DOLBY DIGITAL
◆ RGB signals
• RGB (COMPONENT OFF) (page 35)
PCM
OFF
OFF
ON
DTS:
48kHz/96kHz PCM:
Press ENTER.
The Setup Display for selecting the type
of jack used to connect your audio
component appears.
13Press X/x to select whether or
not to send a DTS signal to your
audio component.
Is this player connected to an amplifier
(receiver) ? Select the type of jack you
are using.
If your audio component has a DTS
decoder, select “ON.” Otherwise, select
“OFF.”
YES
LINE OUTPUT L/R (AUDIO)
DIGITAL OUTPUT
NO
14Press ENTER.
Quick Setup is finished and connections
are complete.
10Press X/x to select the type of
jack (if any) you are using to
connect to an audio component,
then press ENTER.
If your audio component has an MPEG
audio decoder, set “MPEG” to “MPEG”
b
Select “NO,” if you do not connect an
audio component, then go to step 14.
the selection for “TV TYPE” is skipped.
17
Connecting a USB Device
(DVP-NS728H only)
You can connect a USB device to the USB
jack of the player to play video, photo, or
music files. For a list of USB devices that can
be connected to the player, refer “Playable
USB Devices” (supplement). For details on
Refer to the operating instructions supplied
with the USB device before connecting it to
the player.
USB device
To play data files, see “Playing video, photo,
To remove the USB device
Stop playback and disconnect the USB device
from the USB jack.
b
• Take the precaution of backing up important files
on the USB device before connecting it to the
player.
• Do not forcibly connect the USB device and make
sure the plug is oriented correctly.
• Do not connect the player and the USB device
through a USB hub.
• Make sure no virus-infected files are contained on
a USB device before use.
• This player supports USB Mass Storage Class
only.
• This player supports USB device with FAT12,
FAT16, or FAT32 format only.
• Some USB devices may not work with this player.
18
The TV’s input will also switch to the player
automatically, in the following cases:
– You press N, TOP MENU, MENU, or
DISPLAY buttons on the remote.
Playback
Note that these buttons are not effective
when you play audio CD or music files in
“MUSIC” mode.
Playing Discs
– If a disc with auto play function is loaded.
– If you push the disc tray to close.
1
2
Switch the input selector on your
TV so that the signal from the
player appears on your TV screen.
z
You can have the player turned off automatically
whenever you leave it in stop mode for more than
30 minutes. To turn this function on or off, set
“AUTO POWER OFF” in “CUSTOM SETUP” to
Press Z on the player, and place a
disc on the disc tray.
b
• Depending on the DVD or VIDEO CD, some
operations may be different or restricted.
Refer to the operating instructions supplied with
your disc.
• Discs created on DVD recorders must be correctly
finalized before they can be played. For more
information about finalizing, refer to the
operating instructions supplied with the DVD
recorder.
Playback side
facing down
Note on playing DTS sound tracks on a
DVD VIDEO
DTS audio signals are output only through the
DIGITAL OUT (COAXIAL)/HDMI OUT
jack.
3
Press N.
The disc tray closes. The player starts
playback (continuous play). Adjust the
volume on the TV or the audio
component.
Depending on the disc, a menu may
appear on the TV screen. For DVD
To resume playback from the point where
you stopped the disc (Multi-disc Resume)
When you press N again after you stop
playback, the player starts playback from the
point when you pressed x.
If a disc is inside the player
Press N.
z
• To play from the beginning of the disc, press x
twice, then press N.
To stop playback
• With DVD VIDEOs and VIDEO CDs, the player
stores the point where you stopped the disc for up
to 6 discs and resumes playback the next time you
insert the same disc. If you store a resume
playback point for the seventh disc, the resume
playback point for the first disc is deleted.
Press x.
To pause playback
Press X.
One-Touch Play (for HDMI connections
only)
With one touch of the N button on the
remote, the player and your TV automatically
turn on and the TV’s input is switched to the
player. Playback starts automatically.
,continued
19
b
• “MULTI-DISC RESUME” in “CUSTOM
SETUP” must be set to “ON” (default) for this
• Resume Play does not work during Shuffle Play
and Programme Play.
• With some discs, Resume Play may not work,
depending on the point you stop playback, or if
you press [/1.
To play VIDEO CDs with PBC functions
(PBC Playback)
PBC (Playback Control) allows you to play
VIDEO CDs interactively using the menu on
your TV screen.
When you start playing a VIDEO CD with
PBC functions, the menu for your selection
appears.
Select an item using the number buttons, and
press ENTER. Then, follow the instructions
in the menu (press N when “Press
SELECT” appears).
To return to the menu
Press O RETURN.
z
To play without using PBC, press ./> or the
number buttons while the player is stopped to select
a track, then press N or ENTER.
“Play without PBC” appears on the TV screen and
the player starts continuous play. You cannot play
still pictures such as a menu.
To return to PBC playback, press x twice then
press N.
20
Control Menu display (Magic Pad)
Use the Control Menu to select a function and to view related information. Press DISPLAY
repeatedly to turn on or change the Control Menu display as follows:
, Control Menu display 1
m
Control Menu display 2 (Except CD and when “MEDIA” is set to “MUSIC”)
m
Control Menu display off
The Control Menu display 1 and 2 will show different items depending on the media type.
Example: Control Menu display 1 when playing a DVD VIDEO.
Press X/x to select the Control Menu item, then press ENTER.
2
Currently playing chapter number*
1
Currently playing title number*
1
Total number of titles*
Playback status
(N Playback,
X Pause,
2
Total number of chapters*
x Stop, etc.)
Control Menu items
Type of disc
being played*
3
(
)
)
1 2 2 7
DVD VIDEO
(
1 8 3 4
4
Playing time*
T
1 : 3 2 : 5 5
Selected item
Current setting
OFF
OFF
SET
ON
Options
Function name of
selected Control
Menu item
PROGRAM
ENTER
DISPLAY
Quit:
Operation message
1
* Displays the album number for video, photo, and
music files, scene number for VIDEO CDs (PBC
is on), and track number for VIDEO CDs/CDs.
2
* Displays the video, photo, music files numbers,
and index numbers for VIDEO CDs.
* Displays Super VCD as “SVCD.”
* Displays the date for photo files.
3
4
,continued
21
Plays the title, chapter, or track in
random order.
List of Control Menu items
Item
Item Name, Function
TITLE/SCENE/TRACK
CHAPTER/INDEX
Plays all titles/tracks/albums or a
single title/chapter/track/album/file
repeatedly.
TRACK
Selects the title, scene, track,
chapter, or index to be played.
A-B REPEAT (page 27)
Specifies the parts you want to play
repeatedly.
1
Press X/x to select the search
method.
PARENTAL CONTROL
Set to prohibit playback on this
player.
“** (**)” is selected (** refers
to a number).
2
3
Press ENTER.
“** (**)” changes to “-- (**).”
QUICK:
Use Quick Setup to choose the
desired language of the on-screen
display, the aspect ratio of the TV
and the audio output signal.
Press the number buttons to
select the number you want to
search.
4
Press ENTER.
CUSTOM:
TIME/TEXT
In addition to the Quick Setup
setting, you can adjust various other
settings.
Checks the elapsed time and the
remaining playback time.
Input the time code for picture and
music searching (DVD and DivX
video files only).
RESET:
Returns the settings in “SETUP” to
the default setting.
1
2
Press ENTER.
ZOOM
Magnifies the image up to four times
the original size, and scroll using C/
X/x/c.
To return to normal view, press
CLEAR.
Input the time code using the
number buttons, then press
ENTER.
For example, to find the scene at
2 hours, 10 minutes, and 20
seconds after the beginning, just
enter “2:10:20.”
This function is available for all
pictures except a background image.
ANGLE
Changes the angle.
b
You cannot search for a scene on a
DVD+RW/DVD+R/DVD+R DL
using the time code.
CUSTOM PICTURE MODE
Selects the picture quality that best
suits the programme you are
watching.
DISC/USB for DVP-NS728H
only (page 31)
Selects either USB or DISC
playback mode.
SHARPNESS (page 28)
Exaggerates the outline of the image
to produce a sharper picture.
ORIGINAL/PLAY LIST
Selects the type of titles (DVD-VR
mode) to be played, the ORIGINAL
one, or an edited PLAY LIST.
AV SYNC (page 28)
Adjust the delay between the picture
and sound.
PROGRAM (page 25)
Selects the title, chapter, or track to
play in the order you want.
22
z
TVS (TV Virtual Surround)
Selects surround sound effect when
connecting a stereo TV or 2 front
speakers. This only works when
playing a multichannel Dolby audio
sound track. Furthermore, if the
player is set up to output the signal
from the DIGITAL OUT
(COAXIAL)/HDMI OUT jack, the
surround effect will only be heard
when “DOLBY DIGITAL” is set to
“D-PCM” and “MPEG” is set to
“PCM” in “AUDIO SETUP”
The Control Menu icon indicator lights up in green
t
when you select any item
except “OFF” (“PROGRAM,” “SHUFFLE,”
“REPEAT,” “A-B REPEAT,” “SHARPNESS,”
“ZOOM,” “TVS” only). The “ORIGINAL/PLAY
LIST” indicator lights up in green when you select
“PLAY LIST” (default setting). The “ANGLE”
indicator lights up in green when you can change
the angle. The “CUSTOM PICTURE MODE”
indicator lights up in green when any setting other
than “STANDARD” is selected. The “AV SYNC”
indicator lights up in green when set to more than 0
ms.
◆ Items for DATA discs or USB (DVP-NS728H
only)
The default setting is underlined.
• OFF
Cancels the setting.
Item
Item Name, Function
ALBUM
Selects the album that contains
music and photo files to be played.
• TVS DYNAMIC THEATER
• TVS DYNAMIC
• TVS WIDE
This mode is effective when the
distance between the front L and R
speakers is short, such as with built-
in speakers on a stereo TV.
FILE
Selects the photo file to be played.
ALBUM
Selects the album that contains video
file to be played.
• TVS NIGHT
This feature is useful when you want
to hear the dialogue and enjoy the
surround sound effects of “TVS
WIDE” at low volume.
FILE
Selects the video file to be played.
DATE
Displays the date the picture was
taken by a digital camera.
• TVS STANDARD
Use this setting when you want to
use TVS with 2 separate speakers.
Specifies the duration for which the
slides are displayed on the screen.
b
Selects the effects to be used for
changing slides during a slide show.
• When you select one of the TVS
modes, turn off the surround setting
of the connected TV or audio
component.
• The TVS effects do not work when
using the Fast Play or Slow Play
functions, even though you can
change the TVS modes.
• If you use the DIGITAL OUT
(COAXIAL)/HDMI OUT jack and
set “DOLBY DIGITAL” to
“DOLBY DIGITAL,” “MPEG” to
“MPEG,” and “DTS” to “ON” in
“AUDIO SETUP,” sound will come
from your speakers but it will not
have the surround effect.
MEDIA
VIDEO: plays video files.
PHOTO/MUSIC: plays photo and
music files as a slide show.
PHOTO (BGM): plays photo files
with the player’s internal
background sound. To choose the
melody of the background sound,
press AUDIO repeatedly while
viewing the image.
MUSIC: plays music files.
b
• Depending on the contents, the
player will play all files regardless of
the “MEDIA” settings.
23
Guide to the ‘BRAVIA Sync’ Display
You can control the player by selecting the SYNC MENU button on the TV’s remote or TV’s
option menu.
‘BRAVIA Sync’ display
The ‘BRAVIA Sync’ display will show different items depending on the disc type.
Example: ‘BRAVIA Sync’ display when playing a DVD VIDEO
z
Select an item using C/X/x/c and then press
ENTER.
You can also control these functions on the player’s
remote.
◆ When playing a DVD VIDEO
Displays MENU and TOP MENU.
b
• The items in the ‘BRAVIA Sync’ display have the
same functions as the player’s remote buttons
(page 7).
• You can only use this function if your TV
supports the ‘BRAVIA Sync’.
◆ When playing in DVD-VR mode
Displays ., >, and chapter number.
◆ When playing a CD, VIDEO CD, or Super
VCD (without PBC)
Displays ., >, and track number.
• For more details of ‘BRAVIA Sync’, please refer
to the operating instructions supplied with the TV.
◆ When playing a VIDEO CD or Super VCD
(with PBC) (page 20)
Displays ., >, and scene number.
When the disc’s menu appears, you can select
an item by pressing X/x.
◆ When playing video, photo, and music
files
Displays MENU and PICT. NAVI (Picture
Navigation).
To change the display
Press SYNC MENU on the TV’s remote
repeatedly to turn or change the display.
‘BRAVIA Sync’ display and Control Menu
are displayed alternately.
To turn off the display
Press RETURN or SYNC MENU button on
the TV’s remote repeatedly.
24
PROGRAM
ALL CLEAR
T
C
Various Play Mode
Functions
You can set the following play modes:
• Programme Play (page 25)
• Shuffle Play (page 26)
– –
1. TITLE
– –
01
02
03
04
05
ALL
– –
– –
– –
– –
– –
– –
2. TITLE
3. TITLE
4. TITLE
5. TITLE
6. TITLE
7. TITLE
01
02
03
04
05
06
• Repeat Play (page 26)
• A-B Repeat Play (page 27)
Recorded chapters
b
3 Select the title, chapter, or track you
want to programme.
The play mode is cancelled when:
– you open the disc tray.
– you remove the USB device (DVP-NS728H
only).
– you press [/1 and the player enters standby mode.
– you change the setting of “DISC/USB” (DVP-
NS728H only).
◆ When playing a DVD VIDEO
For example, select chapter “03” of title
“02.”
Press X/x to select “02” under “T,” then
press ENTER.
PROGRAM
Creating your own
T
C
ALL CLEAR
– –
– –
ALL
1. TITLE
2. TITLE
3. TITLE
4. TITLE
5. TITLE
6. TITLE
7. TITLE
programme (Programme Play)
– –
– –
– –
– –
– –
– –
01
02
03
04
05
06
01
02
03
04
05
You can play the contents in the order you
want. You can programme up to 99 titles,
chapters, and tracks.
Next, press X/x to select “03” under “C,”
1 After selecting
(PROGRAM)
then press ENTER.
X/x to select “SET t,” then press
ENTER.
PROGRAM
T
ALL CLEAR
–
– –
1. TITLE 0 2 0 3
– –
“TRACK” is displayed when you play
a VIDEO CD or CD.
2. TITLE
01
02
03
04
05
– –
– –
– –
– –
– –
3. TITLE
4. TITLE
5. TITLE
6. TITLE
7. TITLE
PROGRAM
T
ALL CLEAR
– –
1. TITLE
2. TITLE
3. TITLE
4. TITLE
5. TITLE
6. TITLE
7. TITLE
– –
– –
– –
– –
– –
– –
01
02
03
04
05
Selected title and chapter
◆ When playing a VIDEO CD or CD
For example, select track “02.”
Press X/x to select “02” under “T,” then
press ENTER.
Recorded titles or tracks
Selected track
2 Press c.
The cursor moves to the title or track row
“T” (in this case, “01”).
0:15:30
T
PROGRAM
ALL CLEAR
1. TRACK
2. TRACK
3. TRACK
4. TRACK
5. TRACK
6. TRACK
7. TRACK
– –
0 2
– –
– –
– –
– –
– –
– –
01
02
03
04
05
Total time of the programmed tracks
,continued
25
4 Repeat steps 2 to 3, to programme
1 After selecting
(SHUFFLE) on
other titles, chapters, or tracks.
The programmed titles, chapters, and
tracks are displayed in the selected order.
x to select the item to be shuffled.
◆ When playing a DVD VIDEO
• TITLE
• CHAPTER
5 Press N.
Programme Play begins.
When the programme ends, you can
restart the same programme again by
pressing N.
◆ When playing a VIDEO CD or CD
• TRACK
◆ When Programme Play is activated
• ON: shuffles titles, chapters, or tracks
selected in Programme Play
To return to normal play
Press CLEAR, or select “OFF” in step 1. To
play the same programme again, select “ON”
in step 1 and press ENTER.
2 Press ENTER.
Shuffle Play starts.
To change or cancel a programme
To return to normal play
Press CLEAR, or select “OFF” in step 1.
1
Follow step 1 of “Creating your own
z
2
Select the programme number of the title,
chapter, or track you want to change or
cancel using X/x and press c. If you
want to delete the title, chapter, or track
from the programme, press CLEAR.
• You can set Shuffle Play while the player is
stopped. After selecting the “SHUFFLE” option,
press N. Shuffle Play starts.
• Up to 200 chapters in a disc can be played in
random order when “CHAPTER” is selected.
3
Follow step 3 of “Creating your own
programme (Programme Play)” for new
programming. To cancel a programme,
select “--” under “T,” then press ENTER.
b
You cannot use this function with VIDEO CDs or
Super VCDs with PBC playback.
Playing repeatedly
(Repeat Play)
To cancel all of the titles, chapters, or
tracks in the programmed order
Press X and select “ALL CLEAR” in step 2 of
“Creating your own programme (Programme
Play)” and press ENTER.
You can play all of the titles or tracks, or a
single title, chapter, or track repeatedly.
You can use a combination of Shuffle or
Programme Play modes.
z
You can perform Repeat Play or Shuffle Play of
programmed titles, chapters, or tracks. During
Programme Play, follow the steps of Repeat Play
1 After selecting
(REPEAT) on
x to select the item to be repeated.
• DISC: repeats all of the titles, tracks, or
albums. (Select ORIGINAL or PLAY
LIST in DVD-VR mode)
b
• When you programme tracks on a Super VCD, the
total playing time is not displayed.
• You cannot use this function with VIDEO CDs or
Super VCDs with PBC playback.
• USB: repeats all albums (DVP-
NS728H only)
• TITLE: repeats the current title
• CHAPTER: repeats the current chapter
• TRACK: repeats the current track
• FILE (video files only): repeats the
current file
Playing in random order
(Shuffle Play)
You can have the player “shuffle” titles,
chapters, or tracks. Subsequent “shuffling”
may produce a different playing order.
• ALBUM: repeats the current album
26
b
◆ When Programme Play or Shuffle Play
• A-B Repeat Play does not work across multiple
titles.
• You may not set A-B Repeat Play for contents in
DVD-VR mode that contains still pictures.
is activated
• ON: repeats Programme Play or Shuffle
Play
2 Press ENTER.
Repeat Play starts.
To return to normal play
Press CLEAR, or select “OFF” in step 1.
b
You cannot use this function with VIDEO CDs or
Super VCDs with PBC playback.
Repeating a specific
portion (A-B Repeat Play)
You can play a specific portion of a title,
chapter, or track repeatedly.
1 After selecting
(A-B REPEAT)
X/x to select “SET t,” then press
ENTER.
The “A-B REPEAT” setting bar appears.
A 18 - 1:32:30
B
2 During playback, when you find the
starting point (point A) of the portion to
be played repeatedly, press ENTER.
The starting point (point A) is set.
A 18 - 1:32:55 B 18 - 1:33:05
3 When you reach the ending point
(point B), press ENTER again.
The set points are displayed and the
player starts repeating this specific
portion.
To return to normal play
Press CLEAR, or select “OFF” in step 1.
27
b
• This functiondoes not workwhen “PhotoTV HD”
• This function does not work if your TV supports
Theatre mode and it is set to “On.” For more
details, refer to the operating instructions supplied
with the TV.
Customizing the
Playback Configuration
Adjusting the playback
picture (CUSTOM PICTURE MODE)
Sharpening the picture
(SHARPNESS)
You can adjust the video signal from the
player to obtain the picture quality you want.
You can enhance the outlines of images to
produce a sharper picture.
1 After selecting
(CUSTOM
1 After selecting
(SHARPNESS)
X/x to select a level.
PICTURE MODE) on the Control Menu
setting you want.
The default setting is underlined.
• OFF: cancels this option
• 1: enhances the outline
The default setting is underlined.
• STANDARD: displays a standard
picture
• 2: enhances the outline more than 1
• DYNAMIC 1: produces a bold
dynamic picture by increasing the
picture contrast and the colour intensity
• DYNAMIC 2: produces a more
dynamic picture than DYNAMIC 1 by
further increasing the picture contrast
and colour intensity
• CINEMA 1: enhances details in dark
areas by increasing the black level
• CINEMA 2: white colours become
brighter and black colours become
richer, and the colour contrast is
increased
2 Press ENTER.
The selected setting takes effect.
b
• This functiondoes not workwhen “PhotoTV HD”
• This function does not work if your TV supports
Theatre mode and it is set to “On.” For more
details, refer to the operating instructions supplied
with the TV.
Adjusting the delay
between the picture and sound
(AV SYNC)
• MEMORYt: adjusts the picture in
greater detail
When the sound does not match the pictures
on the screen, you can adjust the delay
between the picture and sound.
PICTURE
Changes the contrast.
BRIGHTNESS Changes the overall
brightness.
1 After selecting
(AV SYNC) on
COLOR
HUE
Makes the colours
deeper or lighter.
to select “SET t,” then press ENTER.
The “AV SYNC” adjustment bar
appears.
Changes the colour
balance.
2 Press ENTER.
The selected setting takes effect.
z
When you watch a movie, “CINEMA 1” or
“CINEMA 2” is recommended.
AV SYNC
0ms
28
• OFF t: Turns off the Custom Parental
Control function
2 Press c repeatedly to adjust the
delay.
Each time you press C/c, the delay is
adjusted by 10 milliseconds.
Parental Control (limited playback)
3 Press ENTER.
You can set a playback limitation level.
The selected setting takes effect.
1
After selecting
(PARENTAL
CONTROL) on the Control Menu
t,” then press ENTER.
To reset the “AV SYNC” setting
Press CLEAR in step 2.
The password is required.
2
Enter or re-enter your 4-digit password
using the number buttons, then press
ENTER.
The display for setting the playback
limitation level appears.
b
• This function is not effective if you use the
DIGITAL OUT (COAXIAL) jack, and set
“DOLBY DIGITAL,” “MPEG,” or “DTS” in
“AUDIO SETUP” to “DOLBY DIGITAL,”
• This function is not effective if you connect a
Dolby Digital or DTS-compliant device via the
HDMI OUT jack, and set “DOLBY DIGITAL,”
“MPEG,” or “DTS” in “AUDIO SETUP” to
“DOLBY DIGITAL,” “MPEG,” or “ON”
3
4
Press X/x to select “STANDARD,” then
press ENTER.
The selection items for “STANDARD”
are displayed.
Press X/x to select a geographic area as
the playback limitation level, then press
ENTER.
• For DATA disc or USB (DVP-NS728H only),
this function works for video files only.
The area is selected.
When you select “OTHERS t,” select
and enter a standard code in the table on
page 48 using the number buttons.
Locking discs (PARENTAL
CONTROL)
You can set two kinds of playback restrictions
as following:
• Custom Parental Control
• Parental Control
5
6
Press X/x to select “LEVEL,” then press
ENTER.
The selection items for “LEVEL” are
displayed.
After selecting
(PARENTAL
Select the level you want using X/x, then
press ENTER.
Parental Control setting is complete.
The lower the value, the stricter the
limitation.
the options appear as shown below.
Select the option you want.
The default setting is underlined.
• ON t: Sets the playback restrictions so
that the player will not play inappropriate
discs (Custom Parental Control)
To turn off the Parental Control function,
set “LEVEL” to “OFF.”
• PLAYER t: Playback of some DVD
VIDEOs can be limited according to a
predetermined level such as the age of the
users. Scenes may be blocked or replaced
with different scenes (Parental Control).
(page 29) for detailed settings
• PASSWORD t: Enter a 4-digit password
using the number buttons. The same
password is used for both Custom Parental
Control and Parental Control. Also use this
menu to change the password
z
If you forget your password, remove the disc and
repeat step 1 of “Parental Control (limited
playback).” When you are asked to enter your
password, enter “199703” using the number
buttons, then press ENTER. The display will ask
you to enter a new 4-digit password. After you enter
a new 4-digit password, replace the disc in the
player and press N. When the display for entering
your password appears, enter your new password.
,continued
29
b
Depending on the disc, you may be asked to change
the parental control level while playing the disc. In
this case, enter your password, then change the
level. If the Resume Play mode is cancelled, the
level returns to the previous level.
Playing Video, Photo,
and Music Files
The player can play video, photo, or music
files. For details on playable files, see
b
DATA CDs recorded in KODAK Picture CD
format automatically start playing when inserted.
1
Press MENU.
The list of albums appears.
2
3
Press X/x to select the album.
Press N.
Playback starts from the selected album.
To select a specific video or music file,
press ENTER and press X/x to select a
track or file, and then press ENTER.
To select a specific photo file, see
To stop playback
Press x.
To go to the next or previous page
Press c or C.
To return to the previous display
Press O RETURN.
To go to the next or previous music and
video files
Press > or . during playback.
Note that you cannot return to the previous
album by using ., and that you need to
select the previous album from the album list.
To turn the display on or off
Press MENU repeatedly.
30
– when the player is turned off. This includes
when the player is automatically turned off by
the Auto Power Off function. Press X instead of
x to stop viewing.
– when USB device is removed.
– when “DISC/USB” or “MEDIA” settings are
changed.
To play music with lyrics
Press SUBTITLE while playing music files
that contain unsynchronized lyric
information. To display next/previous line,
press X/x.
z
• By setting “MEDIA” to “PHOTO/MUSIC,” you
can view a slideshow with sound when the music
and photo files are placed in the same album.
• Set “MEDIA” to “MUSIC” to enable lyrics
function.
• Depending on the contents, the player will play all
files regardless of the “MEDIA” settings.
• If the number of viewing times is preset, you can
play DivX video files as many times as the preset
number. The following occurrences are counted:
– when the disc tray is opened.
Selecting a photo file
1 Press MENU.
The list of albums appears.
2 Press X/x to select the album, then
press PICTURE NAVI.
The image files in the album appear in 16
subscreens. A scroll box is displayed on
the right.
– when another file is played.
– when “DISC/USB” (DVP-NS728H only) or
“MEDIA” settings are changed.
1
2
3
4
b
The player supports MP3 ID3 Lyrics only.
5
6
7
8
9
10
14
11
15
12
16
Playing video, photo, and music
files from USB device
13
(DVP-NS728H only)
To display additional images, select a
bottom image and press x. To return to a
previous image, select a top image and
press X.
1 After connecting the USB device
(page 18), select
(DISC/USB)
3 PressC/X/x/cto select the image you
want to view, and press ENTER.
The selected image appears.
2 Press ENTER.
The default setting is underlined.
• DISC: Plays files from a disc
• USB: Plays files from a USB device
To go to the next or previous photo file
Press C or c during playback.
Note that you cannot return to the previous
album by using C. Select the previous album
from the album list.
3 Select USB and follow step 3 of
You can change to DISC mode
automatically by pressing Z without
turning on the Control Menu display.
Press N to start disc playback.
To rotate a photo image
Press X/x while viewing the image. Each
time you press X, the image rotates
counterclockwise by 90 degrees.
To return to normal view, press CLEAR.
Note that the view also returns to normal if
you press C/c to go to the next or previous
image.
b
• For some device, LUN (Logical Unit Number)
may appear. To change the LUN or original
storage, press
when the list of albums
or tracks is displayed.
• If the number of viewing times is preset, you can
play DivX video files as many times as the preset
number. The following occurrences are counted:
– when Z is pressed.
– when another file is played.
,continued
31
b
To display photo information
Press SUBTITLE while viewing photo files.
The detailed information for the selected
photo file appears.
• By connecting to a Sony “PhotoTV HD”
compatible device using an HDMI cord, the TV
will set the optimal image quality for viewing still
picture automatically. For more details, refer to
the operating instructions supplied with the TV.
• “PhotoTV HD” is activated when “JPEG
RESOLUTION” is set to “PhotoTV HD,” photo
playback is available, and the player is connected
to a TV by HDMI cord.
is displayed when the picture was taken
using flash.
is displayed when the image is
automatically rotated.
To hide the information, press SUBTITLE.
Note that the above information may not
appear depending on the digital camera.
• You cannot select “CUSTOM PICTURE MODE”
and “SHARPNESS,” when “PhotoTV HD” mode
is activated.
• When “PhotoTV HD” mode is activated, the
player changes video signal output from “HDMI
RESOLUTION” to “1920×1080i,” “TV TYPE”
to “16:9,” and “YCBCR/RGB (HDMI)” to
“YCBCR” automatically even though the current
settings are kept.
To stop viewing the photo
Press x.
b
PICTURE NAVI does not work if “MUSIC” is
• You cannot select “HDMI RESOLUTION” or
“YCBCR/RGB (HDMI)” in “HDMI SETUP”
(page 40), or “TV TYPE” in “SCREEN SETUP”
activated.
• If you set “PhotoTV HD” mode, the effect,
rotation and zoom functions are not available.
• When “PhotoTV HD” mode is activated, the
selection for “TV TYPE” is skipped during Quick
Viewing a high quality slide
show (PhotoTV HD)
If you have a Sony TV that is compatible with
“PhotoTV HD,” you can enjoy the best
quality images by the following connection
and setting.
1 Connect the player to the TV using an
HDMI cord (not supplied).
Setting the pace for a
slide show (INTERVAL)
You can set the time the slides are displayed
on the screen.
2 Set the TV’s video setting to “Video-A”
mode.
For details about “Video-A,” refer to the
operating instructions supplied with the
TV.
1 After selecting
(INTERVAL) on
x to select a setting.
3 Set “JPEG RESOLUTION” to “PhotoTV
The default setting is underlined.
• NORMAL: sets to standard duration
• FAST: sets a duration shorter than
NORMAL
On “PhotoTV HD”
“PhotoTV HD” allows for highly-detailed
pictures, and photo-like expression of subtle
textures and colors. By connecting Sony
“PhotoTV HD” compatible devices using an
HDMI cord, whole new world of photos can
be enjoyed in breathtaking Full HD quality.
For instance, the delicate texture of the
human skin, flowers, sand, and waves can
now be displayed on a large screen in
beautiful photo-like quality.
• SLOW 1: sets a duration longer than
NORMAL
• SLOW 2: sets a duration longer than
SLOW 1
2 Press ENTER.
b
Duration of interval depends on “JPEG
RESOLUTION” setting in “HDMI SETUP”
32
Selecting the slides’
appearance (EFFECT)
You can select the way the slides are
displayed during a slide show.
1 After selecting
(EFFECT) on
x to select a setting.
The default setting is underlined.
• MODE 1: the images randomly cycle
through the effects
• MODE 2: the next image sweeps in
from top left to bottom right
• MODE 3: the image sweeps in from top
to bottom
• MODE 4: the image sweeps in from left
to right
• MODE 5: the image stretches out from
the centre of the screen
• OFF: turns off this function
2 Press ENTER.
b
• Note that this setting does not work if the JPEG
file has rotation information.
• Depending on the “JPEG RESOLUTION” setting
33
LANGUAGE SETUP
Settings and Adjustments
You can set various languages for the on-
screen display or sound track.
Using the Setup Display
◆OSD (On-Screen Display)
Switches the display language on the screen.
You can make various adjustments to items,
such as picture and sound.
For details on each Setup Display item, see
◆MENU (DVD VIDEO only)
You can select the desired language for the
disc’s menu.
b
◆AUDIO (DVD VIDEO only)
Playback settings stored in the disc take priority
over the Setup Display settings and not all of the
functions described may work.
Switches the language of the sound track.
When you select “ORIGINAL,” the language
given priority in the disc is selected.
1
2
Press DISPLAY when the player is
in stop mode.
◆SUBTITLE (DVD VIDEO only)
Switches the language of the subtitle recorded
on the DVD VIDEO.
When you select “AUDIO FOLLOW,” the
language for the subtitles changes according
to the language you selected for the sound
track.
The Control Menu appears.
Press X/x to select
(SETUP), then press ENTER.
The options for “SETUP” appear.
• QUICK: makes the basic adjustments
• CUSTOM: makes various adjustments
• RESET: resets all the settings explained
z
If you select “OTHERS t” in “MENU,”
“SUBTITLE,” or “AUDIO,” select and enter a
language code from “Language Code List” on
page 48 using the number buttons.
b
3
Press X/x to select “CUSTOM,”
then press ENTER.
If you select a language in “MENU,”
“SUBTITLE,” or “AUDIO” that is not recorded on
a DVD VIDEO, one of the recorded languages will
be automatically selected.
The Setup Display appears.
Select the setup category and adjust each
item following the instructions on pages
LANGUAGE SETUP
OSD:
ENGLISH
ENGLISH
ORIGINAL
ENGLISH
MENU:
AUDIO:
SUBTITLE:
34
becoming damaged (ghosting). Press N to
turn off the screen saver.
SCREEN SETUP
ON
Turns on the screen saver.
Turns off the screen saver.
Choose settings according to the TV to be
connected.
OFF
◆ BACKGROUND
The default settings are underlined.
Selects the background colour or picture on
the TV screen when the player is in stop mode
or while playing a CD, or music files.
◆ TV TYPE
Selects the aspect ratio of the connected TV
(4:3 standard or wide).
You cannot select this when “PhotoTV HD”
JACKET
PICTURE
The jacket picture (still picture)
appears, but only when the
jacket picture is already
recorded on the disc (CD-
16:9
Select this when connecting to a
wide-screen TV or a TV with a
wide mode function.
EXTRA, etc.). If the disc does
not contain a jacket picture, the
“GRAPHICS” picture appears.
4:3
LETTER
BOX
Select this when connecting to a
4:3 screen TV. Displays a wide
picture with bands on the upper
and lower portions of the
screen.
GRAPHICS A preset picture stored in the
player appears.
BLUE
The background colour is blue.
BLACK
The background colour is
black.
4:3
Select this when connecting to a
PAN SCAN 4:3 screen TV. Automatically
displays the wide picture on the
entire screen and cuts off the
◆ LINE
Selects video signals output from the LINE
(RGB)-TV jack on the rear panel of the
player.
portions that do not fit.
VIDEO
Outputs video signals.
16:9
RGB
Outputs RGB signals and no
(COMPONENT component video signals.
OFF)
4:3 LETTER BOX
b
• If your TV does not accept the RGB signals, no
picture will appear on the TV screen, even if you
select “RGB (COMPONENT OFF).” Refer to the
operating instructions supplied with your TV.
• If you set “LINE” to “RGB (COMPONENT
OFF)” in progressive mode, “PROGRESSIVE
(COMPONENT OUT ONLY)” will change from
“ON” to “OFF.”
4:3 PAN SCAN
◆ PROGRESSIVE (COMPONENT OUT
ONLY)
b
Depending on the DVD, “4:3 LETTER BOX” may
be selected automatically instead of “4:3 PAN
SCAN” or vice versa.
If your TV accepts progressive (525p/625p)
format signals, set “PROGRESSIVE
(COMPONENT OUT ONLY)” to “ON.”
Note that you must connect to a progressive
format TV using the COMPONENT VIDEO
◆ SCREEN SAVER
The screen saver image appears when the
player in pause or stop mode for 15 minutes,
or when you play a CD, or music files for
more than 15 minutes. The screen saver will
help prevent your display device from
OFF
ON
To output normal (interlace)
signals.
To output progressive signals.
,continued
35
To output progressive signals
FULL
Select this when you can
change the aspect ratio on your
TV.
1
Select “PROGRESSIVE
(COMPONENT OUT ONLY),” and
press ENTER.
NORMAL
Select this when you cannot
change the aspect ratio on your
TV. Shows a 16:9 aspect ratio
signal with black bands on left
and right sides of the image.
2
3
Select “ON,” and press ENTER.
The display asks for confirmation.
Select “Start,” and press ENTER.
The video switches to a progressive
signal for 5 seconds.
4
If the picture appears normal, select
“YES,” and press ENTER.
If not, select “NO,” and press ENTER.
16:9 aspect ratio TV
To reset the setting
If the picture does not appear normal or goes
blank, press [/1 to turn off the player, and
enter “369” using the number buttons on the
remote, then press [/1 to turn on the player
again.
◆ MODE (PROGRESSIVE)
In order for these images to appear natural on
your screen when output in progressive
mode, the progressive video signal needs to
be converted to match the type of DVD
software that you are watching.
This setting is effective only when you set
“PROGRESSIVE (COMPONENT OUT
ONLY)” in “SCREEN SETUP” to “ON.”
AUTO
Automatically detects the
software type (film-based or
video-based) and selects the
appropriate conversion mode.
Normally, select this position.
VIDEO
Fixes the conversion mode to
the mode for video-based
software.
◆ 4:3 OUTPUT
This setting is effective only when you set
“TV TYPE” in “SCREEN SETUP” to
“16:9.” Adjust this to watch 4:3 aspect ratio.
If you can change the aspect ratio on your TV,
change the setting on your TV, not the player.
36
◆ TRACK SELECTION (DVD VIDEO only)
Gives the sound track which contains the
highest number of channels priority when you
play a DVD VIDEO on which multiple audio
formats (PCM, MPEG audio, DTS, or Dolby
Digital format) are recorded.
CUSTOM SETUP
Use this to set up playback related and other
settings.
OFF
No priority given.
Priority given.
The default settings are underlined.
AUTO
◆ AUTO POWER OFF
Switches the Auto Power Off setting on or
off.
b
• When you set the item to “AUTO,” the language
may change. The “TRACK SELECTION” setting
has higher priority than the “AUDIO” settings in
“LANGUAGE SETUP” (page 34).
ON
The player enters standby mode
when left in stop mode for more
than 30 minutes.
sound track is not played even if you set “TRACK
SELECTION” to “AUTO.”
OFF
Switches this function off.
◆ AUTO PLAY
• If PCM, DTS, MPEG audio, and Dolby Digital
sound tracks have the same number of channels,
the player selects PCM, DTS, MPEG audio, and
Dolby Digital sound tracks in this order.
Switches the Auto Play setting on or off. This
function is useful when the player is
connected to a timer (not supplied).
◆ MULTI-DISC RESUME (DVD VIDEO/
VIDEO CD only)
Switches the Multi-disc Resume setting on or
off. Resume playback can be stored in
memory for up to 6 different DVD VIDEOs/
OFF
ON
Switches this function off.
Automatically starts playback
when the player is turned on by
a timer (not supplied).
◆ DIMMER
Adjusts the lighting of the front panel display.
ON
Stores the resume setting in
memory for up to 6 discs.
BRIGHT
DARK
Makes the lighting bright.
Makes the lighting dark.
OFF
Does not store the resume
setting in memory. Playback
restarts at the resume point only
for the current disc in the player.
AUTO
DARK
Makes the lighting dark if you
do not operate the player or
remote for a short while.
b
If you run Quick Setup, Multi-disc Resume setting
stored in memory may return to the default settings.
◆ PAUSE MODE (DVDs only)
Selects the picture in pause mode.
◆ DivX
AUTO
The picture, including subjects
Displays the registration code for this player.
For more information, go to
on the Internet.
that move dynamically, is
output with no jitter. Normally,
select this position.
FRAME
The picture, including subjects
that do not move dynamically,
is output in high resolution.
37
◆DIGITAL OUT
Selects if audio signals are output via the
DIGITAL OUT (COAXIAL)/HDMI OUT
jack.
AUDIO SETUP
You can set the sound according to the
playback and connection conditions.
ON
Normally, select this position.
When you select “ON,” see
for further settings.
The default settings are underlined.
◆ AUDIO DRC (Dynamic Range Control)
(DVDs only)
Makes the sound clear when the volume is
turned down when playing a DVD that
conforms to “AUDIO DRC.”
OFF
The influence of the digital
circuit upon the analogue circuit
is minimal.
This function affects the output from the
following jacks:
Setting the digital output signal
Switches the method of outputting audio
signals when you connect a component such
as an audio component or MD deck with a
digital input jack.
Select “DOLBY DIGITAL,” “MPEG,”
“DTS,” and “48kHz/96kHz PCM” after
setting “DIGITAL OUT” to “ON.”
If you connect a component that is
incompatible with the selected audio signal, a
loud noise (or no sound) may be heard from
the speakers, risking damage to your ears or
speakers.
– LINE OUT L/R (AUDIO) jacks.
– LINE (RGB)-TV jack.
– DIGITAL OUT (COAXIAL)/HDMI OUT
jack only when “DOLBY DIGITAL” is set
STANDARD Normally, select this position.
TV MODE
Makes low sounds clear even if
you turn the volume down.
WIDE
RANGE
Gives you the feeling of being
at a live performance.
◆ DOWNMIX (DVDs only)
Switches the method for mixing down to 2
channels when you play a DVD which has
rear sound elements (channels) or is recorded
in Dolby Digital format. This function affects
the output of the following jacks:
– LINE OUT L/R (AUDIO) jacks.
– LINE (RGB)-TV jack.
– DIGITAL OUT (COAXIAL)/HDMI OUT
jack when “DOLBY DIGITAL” is set to
b
if you use the DIGITAL OUT (COAXIAL) jack,
and set “DOLBY DIGITAL,” MPEG” or “DTS”
to “DOLBY DIGITAL,” “MPEG” or “ON”
respectively.
if you connect a Dolby Digital or DTS-compliant
device via the HDMI OUT jack, and set “DOLBY
DIGITAL,” “MPEG” or “DTS” to “DOLBY
DIGITAL,” “MPEG” or “ON” respectively.
DOLBY
SUR-
ROUND
Normally, select this position.
Multi-channel audio signals are
output to 2 channels for enjoying
surround sounds.
◆DOLBY DIGITAL (DVDs only)
Selects the type of Dolby Digital signal.
DOLBY
DIGITAL
Select this when the player is
connected to an audio
NORMAL Multi-channel audio signals are
downmixed to 2 channels for use
with your stereo.
component with a built-in
Dolby Digital decoder.
38
b
D-PCM
Select this when the player is
connected to an audio
• When you play a DVD VIDEO with DTS
sound tracks, set “DTS” to “ON” in
• If you connect the player to audio
equipment without a DTS decoder, do not
set “DTS” to “ON” in “AUDIO SETUP”
(page 39). A loud noise may come out from
the speakers, affecting your ears or causing
the speakers to be damaged.
component without a built-in
Dolby Digital decoder. You can
select whether the signals
conform to Dolby Surround
(Pro Logic) or not by making
adjustments to the
“DOWNMIX” item in
• If the HDMI OUT jack is connected to
equipment not compatible with DTS
signals, the “OFF” signals will be
automatically output even when you select
“ON.”
b
If the HDMI OUT jack is connected to equipment
not compatible with DOLBY DIGITAL signals, the
“D-PCM” signals will be automatically output even
when you select “DOLBY DIGITAL.”
◆ 48kHz/96kHz PCM (DVD VIDEO only)
Selects the sampling frequency of the audio
signal.
◆ MPEG (DVDs only)
Selects the type of MPEG audio signal.
PCM
Select this when the player is
connected to an audio
48kHz/16bit The audio signals of DVD
VIDEOs are always converted
to 48kHz/16bit.
component without a built-in
MPEG decoder. If you play
multi-channel MPEG audio
sound tracks, only the Front (L)
and Front (R) signals will be
output from your two front
speakers.
96kHz/24bit All types of signals including
96kHz/24bit are output in their
original format. However, if the
signal is encrypted for
copyright protection purposes,
the signal is only output as
48kHz/16bit.
MPEG
Select this when the player is
connected to an audio
component with a built-in
MPEG decoder.
b
• The analogue audio signals from the LINE OUT
L/R (AUDIO) jacks are not affected by this
setting and keep their original sampling frequency
level.
• If the HDMI OUT jack is connected to equipment
not compatible with 96 kHz/24 bit signals,
48 kHz/16 bit PCM will be automatically output
even when you select “96kHz/24bit.”
b
If the HDMI OUT jack is connected to equipment
not compatible with MPEG audio signal, the
“PCM” signals will be automatically output even
when you select “MPEG.”
◆ DTS
Selects the type of DTS audio signals.
OFF
Select this when the player is
connected to an audio
component without a built-in
DTS decoder.
ON
Select this when the player is
connected to an audio
component with a built-in DTS
decoder.
39
PhotoTV HD Displays extra highly-detailed
picture when connecting to a
Sony’s “PhotoTV HD”-
HDMI SETUP
compatible device.
You can adjust items related to the HDMI
connection.
SD
HD
HD
Displays standard definition
picture with black frame.
The default settings are underlined.
Displays high definition picture
with black frame.
◆ HDMI RESOLUTION
Selects the type of video signals output from
the HDMI OUT jack. When you select
AUTO (1920×1080p) (default), the player
outputs video signals of the highest resolution
acceptable for your TV. If the picture is not
clear, natural or to your satisfaction, try
another option that suits the disc and your
TV/projector, etc. For details, refer also to the
instruction manual supplied with the TV/
projector, etc.
Displays high definition picture
without black frame.
(1920
HD
×
1080i) Displays high definition picture
with black frame at 1920×1080
pixels.
(1920
HD
×
1080i) Displays high definition picture
without black frame at
1920×1080 pixels.
b
You cannot select this when “PhotoTV HD”
• “(1920×1080i) HD
” and “(1920×1080i) HD”
are effective only when you set “HDMI
RESOLUTION” to “1920×1080i” and “TV
TYPE” to “16:9.”
• If you set this setting to “PhotoTV HD,”
“(1920×1080i) HD ” or “(1920×1080i) HD,”
effect, rotation, and zoom function are not
available.
• If you want to use effect, rotation, and zoom
function; sets this setting to “SD
or “HD.”
AUTO
(1920
Normally, select this.
×
1080p)
1920
×
1080i
Sends 1920×1080i video
signals.
1280
×
720p
Sends 1280×720p video
signals.
,” “HD
,”
720×
480/576p Sends 720×480/576p video
signals.
• If you set this setting to “PhotoTV HD,”
“(1920×1080i) HD ” or “(1920×1080i) HD,”
next image appears after black mute.
• HDMI signal will stop momentarily during
loading or unloading DATA disc or USB (DVP-
NS728H only).
• When you set to “PhotoTV HD,” the player
changes video signal output from “HDMI
RESOLUTION” to “1920×1080i,” “TV TYPE”
to “16:9,” and “YCBCR/RGB (HDMI)” to
“YCBCR” automatically even though the current
settings are kept.
To reset the setting
If the picture does not appear normal or goes
blank, press [/1 to turn off the player, and
enter “369” using the number buttons on the
remote, then press [/1 to turn on the player
again.
b
In case of “AUTO (1920×1080p),” the player
automatically adjusts the video signals that are
suitable for the TV.
Other cases, the player directly send the signal even
if TV cannot accept.
• Set this setting to “SD ,” when you want to
view photo files in analogue video outputs with
the HDMI connection.
◆ JPEG RESOLUTION
Selects the type of JPEG resolution so that
you can enjoy high picture quality via your
HDMI connection.
You cannot select this when “HDMI
RESOLUTION” is set to “720×480/576p” or
“TV TYPE” is set to “4:3 LETTER BOX” or
“4:3 PAN SCAN.”
40
◆ YCB
C
R/RGB (HDMI)
◆ LANGUAGE FOLLOW
Selects the type of HDMI signal output from
HDMI OUT jack.
Switches the languages of the DVD player
to the same as the current TV OSD
language.
You cannot select this when “PhotoTV HD”
You cannot select this when “CONTROL
FOR HDMI” is set to “OFF.”
YCBCR
RGB
Outputs YCBCR signals.
Outputs RGB signals.
ON
Switches this function on.
Switches this function off.
OFF
b
• If the playback picture becomes distorted, set this
setting to “RGB.”
b
• Turn off any display before using this function.
• The OSD language for player keeps if the TV’s
language cannot be supported.
• If the HDMI OUT jack is connected to equipment
with a DVI jack, “RGB” signals will be
automatically output even when you select
“YCBCR.”
◆ AUDIO (HDMI)
Selects the type of audio signal output from
the HDMI OUT jack.
AUTO
Normally, select this. Outputs
audio signals according to the
“DIGITAL OUT” settings
PCM
Converts Dolby Digital,
MPEG, or 96 kHz/24 bit PCM
signals to 48 kHz/16 bit PCM.
b
A loud noise (or no sound) will be output if you
connect the player to a TV that is not compatible
with DOLBY DIGITAL/DTS/MPEG signals and
“AUTO” is selected. In this case, select “PCM.”
◆ CONTROL FOR HDMI
Switches the Control For HDMI setting
on or off.
ON
Allows you to use the
CONTROL FOR HDMI
features (page 13).
OFF
Switches this function off.
41
, If the HDMI OUT jack is used for video
output, changing the “HDMI
RESOLUTION” setting in “HDMI
SETUP” may solve the problem (page 40).
Connect the TV and the player using a video
jack other than the HDMI OUT, and switch
the TV’s input to the connected video input
so that you can see the on-screen displays.
Change the “HDMI RESOLUTION”
setting in “HDMI SETUP,” and switch the
TV’s input back to HDMI. If the picture still
does not appear, repeat the steps and try
other options.
Additional Information
Troubleshooting
If you experience any of the following
difficulties while using the player, use this
troubleshooting guide to help remedy the
problem before requesting repairs. Should
any problem persist, consult your nearest
Sony dealer.
, Press [/1 to turn off the player, and enter
“369” using the number buttons on the
remote, then press [/1 to turn on the player
Power
The power is not turned on.
, Check that the mains lead is connected
securely.
There is no picture/picture noise appears
when connected to the HDMI OUT jack.
, Try the following: 1Turn the player off
and on again. 2Turn the connected
Picture
equipment off and on again. 3Disconnect
and then connect the HDMI cord again.
There is no picture/picture noise appears.
, Re-connect the connecting cord securely.
, The connecting cords are damaged.
and switch the input selector on your TV so
that the signal from the player appears on
the TV screen.
, Set “LINE” in “SCREEN SETUP” to an
, The disc is dirty or flawed.
The picture is black and white.
, Set “LINE” in “SCREEN SETUP” to an
, Depending on the TV, the picture on the
screen becomes black and white when you
play a disc recorded in the NTSC colour
system.
, If you are using a SCART cord, be sure to
use one that is fully wired (21-pins).
, The disc is recorded in a colour system that
is different from your TV.
, You set the “PROGRESSIVE
(COMPONENT OUT ONLY)” to “ON” in
your TV cannot accept the progressive
the setting.
Sound
There is no sound.
, Re-connect the connecting cord securely.
, The connecting cord is damaged.
, The player is connected to the wrong input
, The audio component input is not correctly
set.
, Even if your TV is compatible with
progressive format 525p/625p signals and
connected using COMPONENT VIDEO
OUT jacks, the image may be affected when
you set the player to progressive format. In
this case, set the “PROGRESSIVE
, The player is in pause mode or in Slow-
motion Play mode.
, The player is in fast forward or fast reverse
mode.
, If the audio signal does not come through
the DIGITAL OUT (COAXIAL)/HDMI
OUT jack, check the audio settings
, While playing a Super VCD on which the
audio track 2 is not recorded, no sound will
come out when you select “2:STEREO,”
“2:1/L,” or “2:2/R.” Press AUDIO to select
the recorded track.
(COMPONENT OUT ONLY)” in
that the player is set to normal (interlace)
format.
, If you set “LINE” to “RGB (COMPONENT
player outputs no component video signals.
, The player is connected to an input device
42
, When playing multichannel MPEG audio
sound tracks, only the Front (L) and Front
(R) signals will be output from two front
speakers.
, The equipment connected to the HDMI
OUT jack does not conform to the audio
signal format, in this case set “AUDIO
(HDMI)” in “HDMI SETUP” to “PCM”
The disc does not start playing from the
beginning.
, Programme Play, Shuffle Play, Repeat Play,
“Copyright lock” appears and the screen
turns blue when playing in DVD-VR mode.
, Images taken from digital broadcasts, etc.,
may contain copy protection signals, such
as complete copy protection signals, single
copy signals, and restriction-free signals.
When images that contain copy protection
signals are played, a blue screen may appear
instead of the images. It may take a while
when looking for playable images. (For
player that cannot play images that contain
a copy protection only)
No sound is output from the HDMI OUT
jack
, Try the following: 1Turn the player off
and on again. 2Turn the connected
equipment off and on again. 3Disconnect
and then connect the HDMI cord again.
, The HDMI OUT jack is connected to a DVI
device (DVI jacks do not accept audio
signals).
Some functions such as Stop, Fast Play,
Slow Play, Slow-motion Play, Repeat
Play, Shuffle Play, or Programme Play
cannot be performed.
, Depending on the disc, you may not be able
to do some of the operations above.
The sound volume is low.
, The sound volume is low on some DVDs.
The sound volume may improve if you set
“AUDIO DRC” in “AUDIO SETUP” to
Operation
The remote does not function.
, The batteries in the remote are weak.
, There are obstacles between the remote and
the player.
The player does not operate properly.
, When static electricity, etc., causes the
player to operate abnormally, unplug the
player.
, The distance between the remote and the
5 numbers or letters are displayed on the
screen.
, The self-diagnosis function was activated.
player is too far.
, The remote is not pointed at the remote
sensor on the player.
The disc does not play.
, The disc is turned over.
Insert the disc with the playback side facing
down.
The disc tray does not open and “LOCKED”
appears on the front panel display.
, The disc is skewed.
, The player cannot play certain discs
The disc tray does not open and “TRAY
LOCKED” appears on the front panel
display.
, Contact your Sony dealer or local
authorized Sony service facility.
(page 3).
, The region code on the DVD does not match
the player.
, Moisture has condensed inside the player
, The player cannot play a recorded disc that
“Data error” appears on the TV screen
when playing video, photo, and music
The album/track/file names are not
displayed correctly.
files.
, The video, photo, and music files you want
, The player can only display numbers and
to play is broken.
alphabet. Other characters are displayed as
“ ”.
*
,continued
43
The CONTROL FOR HDMI function does
not work.
, Make sure that the connected component is
compatible with the CONTROL FOR
HDMI function. Please refer to the
operating instructions of the component for
detailed explanation.
Self-diagnosis Function
(When letters/numbers appear on the
screen)
When the self-diagnosis function is activated
to prevent the player from malfunctioning, a
five-character service number (e.g., C 13 50)
with a combination of a letter and four digits
appears on the screen. In this case, check the
following table.
, Make sure that the TV’s input is switched to
DVD player so that the signal from the
player appears on the TV screen, and
“CONTROL FOR HDMI” is set to “ON”
‘BRAVIA Sync’ display does not appear.
, Turn off any display of the DVD player
displays. Then, try again.
, Please return to the one screen mode if your
TV is in two screen mode. Then, try again.
First three
characters of action
the service
Cause and/or corrective
number
C 13
The disc is dirty or recorded
in a format that this player
cannot play (page 45).
,Clean the disc with a
cleaning cloth or check its
format.
Your TV automatically turns on or the TV’s
input is switched to the player.
, “CONTROL FOR HDMI” is set to “ON”
(page 41). Switch this function to “OFF”.
C 31
The disc is not inserted
correctly.
Display language on the screen switches
automatically.
,Re-insert the disc
correctly.
, When “LANGUAGE FOLLOW” is set to
display language on the screen
automatically switches, according to the
language setting of the connected TV, if you
change the language settings on your TV,
etc.
USB (DVP-NS728H only)
The player does not detect a USB device
connected to the player.
, The USB device is not securely connected
, The USB device or a cord is damaged.
, Disc mode has not been switched to USB
mode.
, Compatibility with all encoding/writing
softwares, recording devices, and recording
media cannot be guaranteed. Incompatible
USB device may produce noise or
interrupted audio or may not play at all.
44
Playable Media
Type
Disc Logo
Icon
Characteristic
• Commercial DVD
DVD VIDEO
• DVD+RWs/DVD+Rs/
DVD+R DLs in +VR mode
• DVD-RWs/DVD-Rs/DVD-R
DLs in video mode
DVD-VR mode
• DVD-RWs/DVD-Rs/DVD-R
DLs in VR (Video
Recording) mode
CD
• Music CD
• CD-Rs/CD-RWs in music
format
VIDEO CD
• Super VCDs
• CD-Rs/CD-RWs in video
CD/Super VCD format
*
DATA disc or USB
• DATA CD/DATA DVD or
USB devices containing
*
–
video, photo, or music files
*DVP-NS728H only.
2
*
*
Only support movie data of cyber shot.
Files with copyright protection (Digital Right
Management) cannot be played.
MP3 (MPEG-1 Audio Layer III) is a standard
format defined by ISO (International
Organization for Standardization)/IEC
(International Electrotechnical Commission)
MPEG which compresses audio data.
3
Notes about video, photo, or
music files that the player can
play
4
*
The player can play the following files:
File Type
File format Extension
*1
DivX
“.avi” or
“.divx”
The player will play any file in the above
table, even if the file format differs. Playing
such data may generate noise that can result
in speaker damage. The player can play the
following files:
• Photo files that conform to the DCF*
image file format.
• DATA CDs recorded according to ISO
9660** Level 1/Level 2, or its extended
format, Joliet.
• DATA DVDs recorded according to UDF
(Universal Disk Format).
* “Design rule for Camera File system”: Image
standards for digital cameras regulated by JEITA
(Japan Electronics and Information Technology
Industries Association).
**A logical format of files and folders on CD-
ROMs, defined by ISO (International
Organization for Standardization).
Video
*2
MPEG-1
“.mpg” or
“.mpeg”
MPEG-4
(simple
“.mp4” or
“.m4v”
*3
profile)
Photo
Music
JPEG
“.jpeg” or
“.jpg”
*4
MP3
“.mp3”
“.wma”
“.m4a”
*3
WMA
*3
AAC
LPCM/WAVE “.wav”
1
®
*
DivX is a video file compression technology,
developed by DivX, Inc.
DivX, DivX Certified, and associated logos are
trademarks of DivX, Inc. and are used under
license.
,continued
45
z
Region code
Your player has a region code printed on the
back of the unit and only will play
commercial DVDs (playback only) labelled
with identical region codes. This system is
used to protect copyrights.
• If you add numbers (01, 02, 03, etc.) to the front
of the file names, the files will be played in that
order.
• To play a complex hierarchy of folders may take
some time. Create albums with no more than two
hierarchies.
• Set “MEDIA” to “PHOTO/MUSIC” to repeat
both music and photo files. See “Playing
ALL
Commercial DVDs labelled
play on this player.
will also
b
• Some video, photo, and music files may not play,
depending on the encoding/recording condition.
• To start playback and proceed to the next or
another album may take some time.
• The player cannot play music files in mp3PRO or
WMA Pro format.
Depending on the commercial DVD, there
may be no region code indication, even
though playing the commercial DVD is
prohibited by area restrictions.
DVP–XXXX
X
Region code
• If the playing time of either music or photo is
longer, the longer one continues without sound or
image.
00V 00Hz
NO.
00W
0-000-000-00
• To display Progressive photo files or photo files
of 3,000,000 pixels or more may take time and the
duration may seem longer than your selected
setting.
• The player will recognize a maximum of 200
albums, regardless of the selected mode. It can
recognize up to 300 music files and 300 photo
files when “PHOTO/MUSIC” is selected, 600
music files when “MUSIC” is selected, 600 photo
files when “PHOTO (BGM)” is selected, and 600
video files when “VIDEO” is selected.
• The player may not play a combination of two or
more video files.
• The player cannot play a video file of size more
than 720 (width) × 576 (height)/2 GB.
• The player may not play certain video files that
are longer than 3 hours.
• Depending on the file, normal playback may not
be possible. The picture may be unclear, playback
may not appear smooth, the sound may skip, etc.
You are recommended to create the file at a lower
bit rate.
b
• Notes about recordable media
Some recordable media cannot be played on this
player due to the recording quality or physical
condition of the disc, or the characteristics of the
recording device and authoring software.
The disc will not play if it has not been correctly
finalized. For more information, refer to the
operating instructions for the recording device.
Note that some playback functions may not work
with some DVD+RWs/DVD+Rs/DVD+R DLs,
even if they have been correctly finalized. In this
case, view the disc by normal playback. Also
some DATA discs created in Packet Write format
cannot be played.
• Music discs encoded with copyright protection
technologies
This product is designed to playback discs that
conform to the Compact Disc (CD) standard.
Various music discs encoded with copyright
protection technologies are marketed by some
record companies. Please be aware that among
those discs, there are some that do not conform to
the CD standard and may not be playable by this
product.
• The player may not playback the high bit rate
video file on the DATA CD smoothly. You are
recommended to playback using DATA DVD.
• When playing visual data that is not supported by
MPEG-4 format, only sound will be heard.
• For player that cannot play images that
contain a copy protection only
Images in DVD-VR mode with CPRM*
protection may not be played if they contain a
copy protection signal, “Copyright lock” appears
on the screen.
* CPRM (Content Protection for Recordable
Media) is a coding technology that protects the
copyright of images.
46
• Note on DualDiscs
A DualDisc is a two sided disc product which
mates DVD recorded material on one side with
digital audio material on the other side.
However, since the audio material side does not
conform to the Compact Disc (CD) standard,
playback on this product is not guaranteed.
Specifications
System
Laser: Semiconductor laser
Outputs
Note on playback operations of
DVDs and VIDEO CDs
(Jack name: Jack type/Output level/Load
impedance)
LINE OUT (AUDIO):
Phono jack/2 Vrms/10 kilohms
DIGITAL OUT (COAXIAL):
Phono jack/0.5 Vp-p/75 ohms
HDMI OUT:
Some playback operations of DVDs and
VIDEO CDs may be intentionally set by
software producers. Since this player plays
DVDs and VIDEO CDs according to the disc
contents the software producers designed,
some playback features may not be available.
Also, refer to the operating instructions
supplied with the DVDs or VIDEO CDs.
HDMI 19 pin-Standard Connector
COMPONENT VIDEO OUT (Y, PB/CB
,
P
R/CR):
Phono jack/Y: 1.0 Vp-p, PB/CB, PR/ CR
:
0.7 Vp-p/75 ohms
LINE OUT (VIDEO):
Phono jack/1.0 Vp-p/75 ohms
USB (DVP-NS728H only):
About MPEG-4 VISUAL
THIS PRODUCT IS LICENSED UNDER
THE MPEG-4 VISUAL PATENT
USB jack Type A, maximum current
500 mA (For connecting USB device)
PORTFOLIO LICENSE FOR THE
PERSONAL AND NON-COMMERCIAL
USE OF A CONSUMER FOR DECODING
VIDEO IN COMPLIANCE WITH THE
MPEG-4 VISUAL STANDARD (“MPEG-4
VIDEO”) THAT WAS ENCODED BY A
CONSUMER ENGAGED IN A PERSONAL
AND NON-COMMERCIAL ACTIVITY
AND/OR WAS OBTAINED FROM A
VIDEO PROVIDER LICENSED BY MPEG
LA TO PROVIDE MPEG-4 VIDEO.
NO LICENSE IS GRANTED OR SHALL
BE IMPLIED FOR ANY OTHER USE.
ADDITIONAL INFORMATION
General
Power requirements:
220 – 240 V AC, 50/60 Hz
Power consumption:
DVP-NS718H: 11 W
DVP-NS728H: 13 W
Dimensions (approx.):
430 × 43 × 206 mm (width/height/depth)
incl. projecting parts
Mass (approx.): 1.6 kg
Operating temperature: 5 °C to 35 °C
Operating humidity: 25 % to 80 %
INCLUDING THAT RELATING TO
PROMOTIONAL, INTERNAL AND
COMMERCIAL USES AND LICENSING
MAY BE OBTAINED FROM MPEG LA,
LLC. SEE HTTP://WWW.MPEGLA.COM
Supplied accessories
• Remote commander (remote) (1)
• R6 (size AA) batteries (2)
Specifications and design are subject to
change without notice.
47
Language Code List
The language spellings conform to the ISO 639: 1988 (E/F) standard.
Code Language
Code Language
Code Language
Code Language
1027 Afar
1183 Irish
1347 Maori
1507 Samoan
1508 Shona
1509 Somali
1511 Albanian
1512 Serbian
1513 Siswati
1514 Sesotho
1515 Sundanese
1516 Swedish
1517 Swahili
1521 Tamil
1028 Abkhazian
1032 Afrikaans
1039 Amharic
1044 Arabic
1045 Assamese
1051 Aymara
1052 Azerbaijani
1053 Bashkir
1057 Byelorussian
1059 Bulgarian
1060 Bihari
1186 Scots Gaelic
1194 Galician
1196 Guarani
1203 Gujarati
1209 Hausa
1349 Macedonian
1350 Malayalam
1352 Mongolian
1353 Moldavian
1356 Marathi
1357 Malay
1217 Hindi
1226 Croatian
1229 Hungarian
1233 Armenian
1235 Interlingua
1239 Interlingue
1245 Inupiak
1248 Indonesian
1253 Icelandic
1254 Italian
1358 Maltese
1363 Burmese
1365 Nauru
1369 Nepali
1376 Dutch
1379 Norwegian
1393 Occitan
1403 (Afan)Oromo
1408 Oriya
1417 Punjabi
1428 Polish
1435 Pashto;
Pushto
1436 Portuguese
1463 Quechua
1481 Rhaeto-
Romance
1482 Kirundi
1483 Romanian
1489 Russian
1491 Kinyarwanda
1495 Sanskrit
1498 Sindhi
1501 Sangho
1502 Serbo-
Croatian
1525 Telugu
1527 Tajik
1528 Thai
1061 Bislama
1066 Bengali;
Bangla
1067 Tibetan
1070 Breton
1079 Catalan
1093 Corsican
1097 Czech
1103 Welsh
1105 Danish
1109 German
1130 Bhutani
1142 Greek
1144 English
1145 Esperanto
1149 Spanish
1150 Estonian
1151 Basque
1157 Persian
1165 Finnish
1166 Fiji
1529 Tigrinya
1531 Turkmen
1532 Tagalog
1534 Setswana
1535 Tonga
1538 Turkish
1539 Tsonga
1540 Tatar
1257 Hebrew
1261 Japanese
1269 Yiddish
1283 Javanese
1287 Georgian
1297 Kazakh
1298 Greenlandic
1299 Cambodian
1300 Kannada
1301 Korean
1305 Kashmiri
1307 Kurdish
1311 Kirghiz
1543 Twi
1557 Ukrainian
1564 Urdu
1572 Uzbek
1581 Vietnamese
1587 Volapük
1613 Wolof
1632 Xhosa
1665 Yoruba
1684 Chinese
1697 Zulu
1313 Latin
1326 Lingala
1327 Laothian
1332 Lithuanian
1334 Latvian;
Lettish
1171 Faroese
1174 French
1181 Frisian
1503 Singhalese
1505 Slovak
1506 Slovenian
1345 Malagasy
1703 Not specified
Parental Control Area Code List
Code Area
Code Area
Code Area
Code Area
2044 Argentina
2047 Australia
2046 Austria
2057 Belgium
2070 Brazil
2079 Canada
2090 Chile
2165 Finland
2174 France
2109 Germany
2248 India
2238 Indonesia
2254 Italy
2276 Japan
2304 Korea
2363 Malaysia
2362 Mexico
2149 Spain
2376 Netherlands
2390 New Zealand
2379 Norway
2499 Sweden
2086 Switzerland
2528 Thailand
2184 United
Kingdom
2427 Pakistan
2424 Philippines
2436 Portugal
2489 Russia
2092 China
2115 Denmark
2501 Singapore
48
z To find out useful hints, tips and information about Sony products and services
Printed on 70% or more recycled paper using VOC (Volatile Organic Compound)-free
vegetable oil based ink.
Sony Corporation Printed in Malaysia
|