Users Guide & Installation
Handbook
Stoves 60 - 70 - 90cm
Hob Touch UK
Part No 082757504 Date 19/03/2013
Safety
BefoRe UsInG tHe pRoDUct
appliance. cleaning and
Make sure that you have removed all
packaging and wrapping. Some of the
items inside this appliance may have
additional wrapping.
user maintenance shall
not be made by children
without supervision.
GeneRaL
WaRnInG! -
WaRnInG! - The
Unattended cooking on
a hob with fat or oil can
be dangerous and may
result in fire.
appliance and its
accessible parts become
hot during use. care
should be taken to
NEVEr try to extinguish
a fire with water, but
switch off the appliance
and then cover the flame
with a lid or damp cloth.
WaRnInG! - Danger of
fire: Do not store items
on the cooking surfaces.
Never leave any cook
zone on without a pan
covering it. This causes a
fire hazard.
WaRnInG! - Servicing
should be carried out
only by authorised
personnel.
avoid touching heating
elements. children less
than 8 years of age shall
be kept away unless
continously supervised.
This appliance can
be used by children
aged from 8 years and
above and persons with
reduced physical sensory
or mental capabilities or
lack of experience and
knowledge if they have
been given supervision
or instruction concerning
the use of the appliance
in a safe way and
WaRnInG! - The
appliance must never be
disconnected from the
understand the hazards
involved. children
shall not play with the
mains supply
5.162
Safety
during use, as this will
seriously affect the
safety and performance,
particularly in relation
to surface temperatures
becoming hot and gas
operated parts not
correctly fitted.
WaRnInG! - There is
a risk of electric shock,
so always make sure
you have turned off
and unplugged your
appliance before
working efficiently. The
cooling fan (if fitted) is
designed to run on after
the control knob has
been switched off.
starting. Always allow
the product to cool down
before you change a
bulb.
WaRnInG! - Do not
modify the outer panels
of this appliance in any
way.
WaRnInG! - This
appliance must be
earthed.
WaRnInG! - The top
element gets extremely
hot when in use, so take
care to avoid touching it.
WaRnInG! -
Do not spray aerosols
in the vicinity of this
appliance while it is in
operation.
WaRnInG! - Do not
store or use flammable
liquids or items in the
vicinity of this appliance.
WaRnInG! -
Do not modify this
appliance.
WaRnInG! - Do not
Gas WaRnInG! -
If you smell gas:
Do not try to light any
appliance.
operate the appliance
without the glass panel
Do not touch any
5.162
Safety
electrical switch.
contact your local gas
on the hob surface since
they can get hot.
supplier immediately.
Ensure you switch off
the appropriate cook
zone individually or (by
the central on/off key if
touch control) when you
have finished cooking,
do not rely upon the
automatic pan detection
system as your means
of switching “off” the
appliance.
eLectRIc InDUctIon HoB
WaRnInG:-
Unattended cooking on
a hob can be dangerous
and may result in fire.
NEVEr try to extinguish
a fire with water, but
switch off the appliance
and then cover flame
e.g. with a lid or a damp
cloth.
This induction hob
complies with the
Danger of fire: do not
store items on the
cooking surface.
applicable EMc and EMF
standards. Therefore it
should not interfere with
other electronic units.
Persons fitted with a
pacemaker or any other
electrical implant should
clarify with their doctor
or the producer of the
implant, whether there
implant is adequate and
If the surface is cracked,
broken or shattered,
switch off the appliance
to avoid the possibility of
electric shock and call for
a service engineer’s visit.
Metallic objects such as
knives, forks, spoons and
lids should not be placed
5.162
Safety
fail-safe.
the pacemaker
must be designed
in compliance with
the appropriate
regulations.
Prolonged intensive use
of the appliance may call
for additional ventilation,
for example opening
of a window, or more
effective ventilation,
for example increasing
the level of mechanical
ventilation where
caution: This appliance
is for cooking purposes
only. It must not be used
for other purposes, for
example room heating.
present.
Induction Hob
Parts of the appliance
may become hot while
in use. Always make
sure that children
are supervised when
they are near to the
appliance.
Always position pans
over the centre of the
cook zone, and turn
the handles to a safe
position so they cannot
be accidentally knocked
or grabbed.
caution: The use of a
gas cooking appliance
results in the production
of heat, moisture and
products of combustion
in the room in which it is
installed. Ensure that the
kitchen is well ventilated
especially when the
appliance is in use.
Keep natural ventilation
holes open or install a
mechanical ventilation
device (mechanical
Do not leave pans on
extractor hood).
5.162
Safety
the hob when you’re not damaged.
around - take them off
the cook zone if you
have to leave the kitchen
even if you think it will
only be for a moment,
while you answer the
door or phone.
The glass ceramic can
get hot whilst cooking;
even though the cook
zone itself does not
generate heat. The heat
generated is conducted
back from the hot pans.
If you use a griddle plate
ensure it is completely
cool before attempting
to lift it from the hob as
residual heat may cause
burns, Always use oven
gloves to protect your
hands.
Keep electrical leads
from trailing over or
going near the hob.
The appliance must
never be disconnected
from the mains supply
during use as this will
seriously affect the
The appliance has a
glass hob top, make
sure you do not drag
pans across the ceramic
surface as this will
lead to scratches and
damage.
Do not use the hob
surface as a chopping
board or food
safety and performance,
particularly in relation
to surface temperatures
becoming hot and
component parts not
working efficiently. The
cooling fan (if fitted) is
designed to run on after
the control has been
switched off.
preparation area as this
may lead to it becoming
fire safety advice
Most kitchen fires occur when people are
5.162
Safety
distracted or leave things unattended, so
remember:
•
Never use water on an electrical or
cooking oil fire.
If you’re called away from the cooker - by
the phone or someone at the door, either
take pans off the heat, or switch off your
hob.
DIsposaL
packaging Material
The packaging materials used with this
appliance can be recycled.
Don’t let yourself be distracted while
cooking.
Please dispose of the packaging materials
in the appropriate container at your local
waste disposal facilities.
If you do have a fire in the kitchen, don’t
take any risks - get everyone out of your
home and call the Fire Brigade.
Unattended cooking on a hob with fat or
oil can be dangerous and may result in a
fire. NEVER try to extinguish a fire with
water, but switch off the appliance and
then cover flame e.g. with a lid or a fire
blanket.
old appliances
The Symbol
on the product or on
its packaging indicates that this product
may not be treated as household waste.
Instead it should be taken to the appli-
cable collection point for the recycling of
electrical and electronic equipment.
WARNING - If a pan catches fire:
•
Do not move it - it is likely to be
extremely hot
•
Turn off the heat if it’s safe to do so
- but never lean over a pan to reach
the controls.
You will by ensuring the appliance is cor-
rectly disposed of help prevent potential
negative consequences for the environ-
ment and human health.
•
•
If you have a fire blanket, put it over
the pan.
If you have put the fire out, leave the
pan to cool completely.
For additional details regarding the recy-
cling of this product please contact your
local government office, your household
waste disposal service or the retailer
where you purchased the product.
Deep-fat frying presents more
dangers in your kitchen.
•
Never fill a chip pan (or other deep-
fat fryer) more than one-third full of
oil
•
Do not use a fire extinguisher
on a pan of oil - the force of the
extinguisher can spread the fire and
create a fireball.
If you have an electrical fire in the
kitchen:
•
Pull the plug out, or switch off the
power at the fuse box - this may be
enough to stop the fire immediately
•
Smother the fire with a fire blanket,
or use a dry powder or carbon dioxide
extinguisher
5.162
UsInG tHe HoB - eLectRIc (ceRaMIc)
Cooking Surface layout
1
1
2
COOKING ZONES
TOUCH CONTROLS
2
Touch Control Layout
7
4
3
TIMER
1
2
3
4
5
6
7
KEYLOCK
CENTRAL ON/OFF KEY
COOK ZONE KEYS (1 - 4)
POWER LEVEL/COOK ZONE DISPLAY
POWER LEVEL ADJUST (+ / -)
DUAL ZONE KEY (IF FITTED)
TIMER KEY
KEY 2
KEY 3
KEY 4
6
DUAL
KEY
KEY 1
2
1
5
Note; Generic illustrations shown above your
appliance may visually differ.
touch controls
need to apply any pressure. The touch
control keys take approximately 1 second
to respond to your touch.
The touch controls of your hob have been
designed to provide you with finger tip
control of your hob, providing accurate
and repeatable power settings for cooking
and an easy clean surface that can be
easily wiped over, When a cook zone is
activated the power setting is displayed
for each zone individually.
Always ensure the touch control area is
clean, dry and free from any objects (e.g.
utensils, tea towels and cloths), spillages
and water may make the controls difficult
to operate.
A beeping sound will be activated and will
keep on beeping every 10 seconds, to
attract your attention, please remove any
objects and clean the area as appropriate.
Using the touch controls
Use the flat of your finger, not the tip, the
controls respond to touch, so you don’t
UsInG tHe HoB - eLectRIc (ceRaMIc)
appyling power to the Hob
switching on (Individual cook Zone)
Before switching on the power supply to
the appliance, switch off any bright lights
(Such as a cooker hood) and ensure the
appliance is not in direct sunlight.
1, Ensure the Key lock is deactivated.
2, Touch the on/off Key for 1 second a
beep sounds and the cook zone displays
become illuminated.
This is to enable the electronic controls to
calibrate its sensitivity against the natural
ambient lighting (Approx 30 seconds).
3, Touch the required cook zone key, it will
start to flash.
Failure to observe the above will result in
the hob not functioning correctly, (Display
showing “FL”). To rectify remove all strong
lighting sources and re-apply power.
4, Whilst flashing adjust the cook zone
power level as required by using the Up+/
down- keys.
5, Then either touch the cook zone key
again to confirm the setting or after 5-10
seconds the hob will auto set the hob
power and will beep and stop flashing.
The hob should complete the calibration
procedure satisfactorily and lighting such
as cooker hoods can be used normally.
When power is first switched on the hob
will always start up with the Key lock
activated.
note: Quick operation with the power
level at 0 touch the down (-) key will take
the hob straight to power level 9.
Key Lock
6, To adjust the power setting follow steps
A red led indicates when the key lock is
active, to deactivate/activate, touch the
Key lock key for 1 second.
3-5 above.
7, repeat the above as necessary for the
other zones.
The key lock is deactivated when the red
lED switches off.
note: During cooking, the elements will
cycle on and off. This is normal.
If any of the cook zones are oN, the key
lock function locks all the keys except the
oN/oFF key.
Dual Zone (If fitted)
note: The dual zone is only available on
70cm and 90cm appliances, and is where
the inner ring of the heating element can
be controlled separately.
If the cook zones are oFF, the key lock
function locks all the keys, including the
oN/oFF key.
note: The Key lock is automatically ac-
tivated every time the electricity supply is
switched off and back on to the hob.
To avoid unintentional switching on of the
appliance, e.g. by small children and pets,
we recommend activation of the key lock
feature.
2
1
central on/off key
The central on off key activates the cook-
ing zone selection keys and enables all
of the cooking zones to be switched off
simultaneously at a touch of one key.
COOK ZONE KEY (INNER ONLY)
1
2
CENTRAL DUAL ZONE KEY (INNER & OUTER)
Note; Generic illustration shown above your
appliance may visually diꢀer.
UsInG tHe HoB - eLectRIc (ceRaMIc)
to operate the dual cook zone
auto Heat Up
•
Select appropriate cook zone and
•
Select the appropriate cook zone and
set the power level as per the single
zone
increase to power level 9
•
Now press the up (+) key again and
until the red lED is illuminated next
to the cook zone.
•
Whilst the heater display is still flash-
ing press the central dual zone key,
a red lED will illuminate next to the
cook zone to indicate it has been
activated.
•
The power level will still be flashing,
so now select the power level you
would like (use the heat up time table
for guidance).
•
The power level of the cook zone will
stop flashing and the power level is
set.
•
•
once set the red lED is illuminated
once the heat up time as elapsed
a beep will sound and the red led
disappears and the heater remains at
the reduced level.
to de-select the dual cook zone
•
Touch the cook zone Key, the power
level display will start flashing.
power
time
•
Whilst the power level display is flash-
ing press the centre dual zone key
or return the power level to “0” and
the red led will disappear and the
inner and out elements will be discon-
nected. i.e. centre element controlled
only.
Level
Min/sec
1
2
3
4
5
6
7
8
01:11
02:44
04:47
05:28
06:29
01:11
02:44
02:44
note: only the inner ring can be be oper-
ated on its own, the outer ring can only
be operated with the inner ring, match
your pan accordingly.
switching off (Individual cook Zone)
•
Touch the required cook zone key
until the zone display flashes, now
either return the power level to 0 by
pressing the down(-) key or simul-
taneously press the down(-) and up
(+) simultaneously and it will jump
straight to the 0 setting.
note: During the heat up time the power
level is automatically set at full power un-
till the times detailed above have elapsed.
cookware
•
cookware made of enamelled steel
or with aluminium or copper bottoms
can leave discolorations on the ce-
ramic glass surface which are difficult
or impossible to remove.
Residual Heat Indicators (for each
cook Zone)
•
If the glass surface is hot an “H” will
be displayed in the cook zone display
until the glass has sufficiently cooled.
•
You can recognise good cookware
from the bottoms of the pans. The
bottom should be as thick and flat as
possible.
note: “ H” and “0” will flash alternatively
if the cook zone is hot and another cook
zone is in use.
UsInG tHe HoB - eLectRIc (ceRaMIc)
timer (all cook Zones)
Refered
zone
LED’s
All 4 cooking zones can be operated under
the timer independently and at the same
time for up to 99 minutes. When the set
time expires the timer will beep and the
cook zone will switch off automatically.
Timer
Timer adjust indicator
to cancel the timer
Either return the time down to zero or
switch off the cook zone.
to set the timer to a cook Zone
1, Set the desired power level to the cook
zone.
safety shut Down
If the power level is not changed for a
long period of time the cook zone will
automatically turn itself off.
2, Whilst the cook zone power level is
flashing touch the timer key and the timer
will illuminate “00” and two red leds will
illuminate the first one will be flashing on
the timer to indicate the activated timed
cook zone and the second one “00.” Indi-
cates that the time can be adjusted.
The maximum time a cook zone can stay
on depends on the power level.
power Level
Max time
(Hours)
1
2
3
4
5
6
7
8
9
10
5
5
4
3
2
2
2
1
3, Set the required time using the up(+)
and down(-) keys.
4, To adjust the timer whilst in operation
follow steps 2 and 3 above.
note; once the time has elapsed, touch
the timer key to cancel the alarm. When
more than one cook zone is being timed,
touch the cook zone key to view the timer.
trouble shooting Guide - ceramic touch control Hobs
There is
no power
to the hob
The mains switch is not switched
on
Ensure that the switch to the
appliance is switched on and also
check the fuse/circuit breakers to see
if you are experiencing power failure
The hob
has turned
itself off
The power has been switched off
check switches and fuses as above
The control panel is covered with
remove any objects and or cloths
a cloth or object
from the control area
The hob has been switched off
Switch on the hob again after
completing the above steps
accidentally
Display
of F and
letters
If F and letters appear on the
Follow the directions in the Error
display, your unit has detected a codes and Hob Status codes Section
fault, follow the required actions
in the Error and hob status codes
table.
Important Information:- If the appliance has been operated/handled incorrectly,
the engineers visit will be chargeable, even during the warranty period
eRRoR coDes
Hob Status Codes
Fault Description
Action
No Fault " H" will switch off when
glass surface drops below 60oC
H
Residual Heater
Appliance Errors & Alarms
Fault Description
Action
Switch the power off and on, The
system will reset and the hob
should now be working correctly
F0
FA
FU
FJ
FC
Fr
Touch Control Error
Touch Control Error
Touch Control Error
Touch Control Error
Touch Control Error
Touch Control Error
Switch the power off and on,The
system will reset and the hob
should now be working correctly
Switch the power off and on, The
system will reset and the hob
should now be working correctly
Switch the power off and on, The
system will reset and the hob
should now be working correctly
Switch the power off and on, The
system will reset and the hob
should now be working correctly
Switch the power off and on, The
system will reset and the hob
should now be working correctly
Allow hob to cool then Switch the
power off and on, The system will
reset and the hob should now be
working correctly
Fc or F
Overheat/Temperature Problems
Overheat/Temperature Problems
Overheat/Temperature Problems
Poor Ambient Light Conditions
Allow hob to cool then Switch the
power off and on, The system will
reset and the hob should now be
working correctly
FE
Allow hob to cool then Switch the
power off and on, The system will
reset and the hob should now be
working correctly
Ft
Switch off lighting in area, Clean
hob surface, Switch the power off
and on, The system will reset and
the hob should now be working
correctly
FL
If any of the above problems persist please contact the customer service department for further assistance,
energy saving tips
•
•
•
Always place cookware on the cooking zone before it is switched on.
Whenever possible place lids on pans.
Switch off the cook zones off before the end of the cooking time, taking advantage
of residual heat.
•
The bottom of the cookware and the cooking zones should be the same size.
CLEANING
eLectRIc HoB
follow the circular grooves and avoid
damaging the red spots. Make sure
that you allow the hotplate to dry
before use by switching on the ele-
ments at a low heat.
ceramic glass hobs
•
It is recommended that you clean
and wash the hob surface before
using for the first time. Apply a thin
coat of ceramic hob cleaner to the
hob to help maintain and protect it.
•
•
You can restore the hotplates by us-
ing a solid plate cleaner but take care
to avoid the red spots on elements.
•
The ceramic hob top can be cleaned
using a clean, damp cloth or kitchen
paper. Do not use a used dishcloth
or sponge as they can leave a film of
detergent on the surface which can
lead to discoloration. Please ensure
that the elements are cooled fully to
avoid steam burns.
To prime: Switch on each element in
turn for a short while (with no pan on
it) at a medium - high setting. This
will harden and burn off the coating.
•
To season: Heat the element for 30
seconds at a medium setting then
switch off. Use a minimum amount
of unsalted vegetable oil, on a dry
cloth or paper towel, and apply a thin
coat of oil to the element surface.
Wipe off the excess and heat the ele-
ment for one minute.
•
You can use a specialist ceramic
cleaner to restore the surface, but
use sparingly to avoid coating the
hob top too thickly. Too much cream
cleaner will lead to discolouration.
Use a dry, clean cloth to polish the
surface.
notes:
•
The edge of the ceramic glass will
always appear to be a different colour
than the top surface due to the
ground safety edge.
•
•
•
For stubborn marks, a specialist hob
scraper or cleaner can be used.
Do not use steam cleaners or high-
pressure cleaning equipment.
•
Scratches or dark stains on the
ceramic glass that cannot be re-
moved do not affect the function of
the appliance.
regular cleaning will prevent any
salts or minerals from accumulating
on your hob and discolouring the
glass.
safety when cleaning
•
For cleaning, the appliance must be
switched off and cooled down.
•
•
Wipe any spillage as soon as pos-
sible.
WaRnInG! risk of burns from residual
heat.
clean the hob top as regularly as
possible, this will prevent any build
up of grease which may be a fire
hazard.
solid plate hobs
•
Prime and Season - this helps main-
tain the finish of the elements.
•
Use a damp, clean cloth to wipe the
solid plate, making sure that you
installation
General information
between hob base and appliance must be
maintained.
Installation should only be carried out by
a qualified installer or engineer.
Installation above an oven
Please keep to the following points most
carefully;
refer to the manufacturer’s instructions
for clearances above the oven.
Although every care has been taken to
ensure this appliance has no burrs, or
sharp edges, we recommend that you
wear protective gloves when install-
ing and moving this appliance. This will
prevent injury.
We recommend a 25mm gap between the
bottom of the hob and appliance.
Installation above a unit with a
drawer or door
The base of the appliance must be pro-
tected from damage e.g. draws may only
be installed providing a partition panel is
fitted to the required dimensions under-
neath the appliance.
The minimum distances to other appli-
ances and units are to be observed.
Wall surfaces above the work surface and
in the immediate vicinity of the cooking
hob must be heat resistant.
INSTALLATION ABOVE AN OVEN
laminated surfaces and the adhesive
used for fixing them must be heat resis-
tant in order to avoid any damage.
The space for air circulation, located
underneath and at the back of the hob
improves its reliability by ensuring that it
will cool down, efficiently.
Worktop
Oven
Hob
25mm
Installations should be carried out in line
with the National regulations applicable
with this product type.
note: Avoid installing the appliance next
to doors and under windows. This will
avoid the potential for hot cookware
being knocked off the hob when doors
and windows are opened (Risk of burns).
INSTALLATION ABOVE A UNIT WITH
A DRAWER OR DOOR
Worktop
Hob
Built-in appliances may only be used after
they have been built-into suitable built-in
units and surfaces that meet the required
standards.
25mm
Partition
cHoosInG yoUR InstaLLatIon
We recommend that you install this ap-
pliance in a work top which is a minimum
38mm deep.
The hob can be fitted into a work top
less than 38mm deep, but the 25mm gap
installation
clearances and dimension – require-
ments
No shelf or overhang of combustible
material should be closer than 650mm
above the hob.
There must be a minimum clearance of
50mm between the rear edge of the hob
and the rear wall. This clearance must
be maintained up to 650mm above the
worktop.
There must be a minimum clearance of
50mm between the edges of the hob
and any side walls; this clearance must
be maintained up to 420mm above the
worktop.
When installing an extractor hood above
the hob, refer to their Manufacturer’s
instructions.
Minimum distance
between carcasses must
be equal to width of hob
650mm min
*
420mm min
560mm (60cm Hobs)
50mm min
660mm (70cm Hobs)
860mm (90cm Hobs)
50mm min
30mm min /
50mm max
490mm (60 - 70cm Hobs)
370mm (90cm Hobs)
50mm Min
Minimum height to extractor
as recommend in extractor
instruction manual
*
installation
fitting into worktop
Recessed Method
cut a hole in the work surface to the
required size. The worktop must be of
heat-resistant material or covered with
heat-resistant material.
recess the work top to the appropriate
depth (Approx 5mm) and shape to fit the
hob (add 1mm to overall glass size). Refer
to the installation bracket advice to deter-
mine your installation type. Insert the hob
into the recess, ensuring that the foam
seal is sitting correctly. locate and attach
the securing clamps as required, Tighten
the screws so that the hob is pulled down
firmly against the worktop, thus ensuring
a good seal.You may want to fill any gap
between the hob top glass and the work
top surface with silicone sealant.
protecting the cut-out;
The types of chipboard used for work
surfaces swell relatively quickly in contact
with humidity.
Apply a suitable sealant to the cut edge to
protect it from moisture ingress.
This hob can be installed conventionally
(glass above the work top) or recessed
into the work top for a flush fit.
Do not fit silicone sealant under the
glass hob instead of the self adhesive seal.
self adhesive seal
Apply the self adhesive seal to the
underside edges of the hob glass. For best
results, the seal should be adhered along
each side in turn, as close to the edge as
possible, and trimmed at each corner, tak-
ing care to ensure a neat join.
CONVENTIONAL INSTALLATION
1
Worktop
Hob
UNDERSIDE OF HOB
SELF ADHESIVE SEAL
1
SEAL
RECESSED METHOD
2
1
conventional Installation
Worktop
Hob
refer to the installation bracket advice
to determine your installation type. Place
the hob in the aperture, checking the hob
glass is covering the work top along all
four sides.
Set the front edge of the appliance paral-
lel with the front of the work top.
locate and attach the securing clamps
as required, Tighten the screws so that
the hob is pulled down firmly against the
worktop, thus ensuring a good seal.
1
2
SELF ADHESIVE SEAL
SILICONE SEALANT
installation
Installation Bracket advice
Installation pack 2
Secure the hob to the worktop by means
of the brackets provided, taking the thick-
ness of the worktop into account.
4 x cranked installation bracket
4 x Spire clips (70/90cm appliances only)
4 x No8 Screws
UNDERSIDE OF HOB
Depending on your appliance the cranked
bracket may or may not require the spire
clips detailed in pack 1. If your appliance
is not supplied with spire clips, the
installation brackets screw directly into
the base of the hob in the ported holes
provided.
INSTALLATION POSITIONS
1
4
30mm
2
INSTALLATION POSITIONS
3
70 & 90cm
Appliances only
Depending on your appliance it will be
supplied with one of the following
installation packs;
40mm
50mm
Installation pack 1
1
2
3
4
Worktop
Bracket
Screw
4 x “U” shape installation brackets
4 x Spire clips
4 x No8 Screws
Spire clip
The spire clips must be fitted to the base
of the hob prior to fitting the installation
brackets.
1
Important;
Do not modify this appliance.
30mm
4
2
3
1
2
3
4
Worktop
Bracket
Screw
40mm
50mm
Spire clip
installation
connect to tHe eLectRIcIty
sUppLy
•
remove the cable clamp screw and
release the cable clamp retaining
arm.
WaRnInG: This appliance must be
earthed. only connect to the electrical
mains terminal with the power switched
off. The electrical mains terminal is live.
note;
The cable clamp has a ratchet type
mechanism on the right hand side of the
retaining arm.
Follow the terminal block connection
schematic
•
Strip the wires & connect to the
terminal block as appropriate:-
loose and inappropriate connections can
make the terminal overheat.
Ensure the cable clamp is fitted correctly
and securely.
Terminal Block Connection
Schematic
A device must be provided in the
electrical installation which allows the
appliance to be disconnected from the
mains at all poles with a contact opening
of at least 3mm.
We recommend that the appliance is con-
nected by a competent person who is a
member of a “competent Person Scheme”
who will comply with the required local
regulations.
5
4
connection should be made with a suit-
able cable.
•
Firstly open the terminal block cover
using a small flat bladed screwdriver
in the door release tabs shown below.
BROWN / L1
4
5
Live
230V.....240V
BLUE / N
GREEN/YELLOW / PE
3
Neutral
Earth
1
2
•
•
Fit the cable clamp & secure with the
screw provided.
close the terminal box, ensuring that
the cover is closed and all screws are
tight and in place.
1
2
3
Door release tab
Important: Ensure that you route all
mains electrical cables well away from any
adjacent heat source, such as the base of
the hob an oven or grill.
Cable clamp ratchet
Cable clamp screw
tecHnIcaL Data
sUppLy: 220 -240V ~ 50Hz 5.04kW - 6.4kW
Refer to the data badge on the under side of your hob for specific power rating of your model
CUSTOMER CARE
cUstoMeR caRe WeB sHop
range of Bake ware and cookware essen-
tials including roasting Pans, cake Tins
Having purchased a superior cooker, hob
or hood from us, you’ll naturally want to
keep it looking great. And who better to
help you care for it than the manufac-
turer?
and Non-Stick cooking liners.
For all enquires, please visit our Web
call the Spares Sales Team on 0844
815 3745. For countries outside the UK,
please contact your local service agent.
We offer an extensive range of accesso-
ries, components and cleaning products
which, will instantly give your cooker a
good as new look.
In addition to the list of our most popular
products below, we also have an exciting
product De-
Where used
scription
purpose
Enables easier cleaning of your ceramic hob.
Prevents build up of mineral deposits. Best
used with ceramic Hob Scraper Kit. 300ml
bottle.
All ceramic glass
ceramic Hob
hobs including
cleaner
Induction
All ceramic glass
ceramic Hob
Ideal for removing cooked on marks from
ceramic glass hobs Best used with ceramic
Hob cleaner
hobs including
Scraper kit
Induction
Sealed Hotplate
conditioner
All sealed/solid
plate hobs
Restores the sleek matt black finish to solid
hotplates
Multipurpose
Kitchen cleaner
General kitchen
cleaner
Excellent multipurpose cleaner, For use
around the kitchen. 500ml bottle.
All cooking appli- cuts through grease & burnt on grime. 500ml
ances. bottle
oven cleaner
All cooking appli- chemical free cleaning cloth Ideal for clean-
ances. ing & polishing glass & stainless steel
restor-A-cloth
Stainless Steel
cleaner
All stainless steel oil based cleaner. Perfect for removing stub-
parts
born & greasy marks. 300ml bottle.
New filters, help to maintain efficient cooker
hood operation and keep your Kitchen odour
free
rectangular car-
cooker Hoods
cooker Hoods
bon filters
New filters, help to maintain efficient cooker
hood operation and keep your Kitchen odour
free
round carbon
Filters
15.030
Please keep this handbook for future reference, or for anyone else
who may use the appliance.
Please keep this handbook for future reference, or for anyone else
who may use the appliance.
CcUSsTtOoMEeR CcAaREe
To contact Stoves about your appliance, please call
Warranty Registration
0844 481 0182
to register your appliance
customer care Helpline
0844 815 3740
in case of difficulty within the UK
Alternatively general, spares and service information is available from our website at
Please ensure that you have the product’s model no and serial no available when you
call. These can be found on the silver data label on your product which is located:
ovens
open the door; adjacent to the oven cavity
Inside the base compartment
on the underside of the product
High-level grill products
Hobs
Enter appliance numbers here for future reference:
Model No
Serial No
seRVIce RecoRD
Date of purchase
Installed by
Installation Date
Place of purchase:
Date
Part(s) replaced
Engineer’s name
For customers outside the UK and Northern Ireland, please contact your local supplier.
Glen Dimplex Home Appliances, Stoney lane, Prescot, Merseyside, l35 2XW
|