Sunbeam Remote Controlled
Tower Fan
Instruction Booklet
FA7200 90cm Remote Controlled Tower Fan
Please read these instructions carefully
and retain for future reference.
Sunbeam’s Safety Precautions
Sunbeam are very safety conscious when
designing and manufacturing consumer prod-
ucts, but it is essential that the product user
also exercise care when using an electrical
appliance. Listed below are precautions which
are essential for the safe use of an electrical
appliance:
•
•
Do not use an appliance for any purpose other
than its intended use.
Do not place an appliance on or near a hot gas
flame, electric element or on a heated oven. Do
not place on top of any other appliance.
Do not let the power cord of an appliance hang
over the edge of a table or bench top or touch
any hot surface.
For safety reasons and to avoid maintenance
by unskilled persons, some appliances are
‘sealed’ using tamperproof screws. Such
appliances should always be returned to the
nearest Sunbeam Appointed Service Centre for
adjustment or repair if required.
•
•
•
•
Read carefully and save all the instructions
provided with an appliance.
Always turn the power off at the power outlet
before you insert or remove a plug. Remove by
grasping the plug - do not pull on the cord.
•
•
Turn the power off and remove the plug when
the appliance is not in use and before cleaning.
•
Do not operate any electrical appliance with a
damaged cord or after the appliance has been
dropped or damaged in any manner. If damage
is suspected, return the appliance to the
nearest Sunbeam Appointed Service Centre for
examination, repair or adjustment.
For additional protection, Sunbeam recommend
the use of a residual current device (RCD)
with a tripping current not exceeding 30mA in
the electrical circuit supplying power to your
appliances.
Do not use your appliance with an extension
cord unless this cord has been checked and
tested by a qualified technician or service
person.
Always use your appliance from a power
outlet of the voltage (A.C. only) marked on the
appliance.
Close supervision is necessary when your
appliance is being used near children or infirm
persons.
Never leave an appliance unattended while in
use.
•
•
•
•
•
•
Do not immerse the appliance in water or any
other liquid.
Young children should be supervised to ensure
that they do not play with the appliance.
If you have any concerns regarding the performance and use of your appliance,
Ensure the above safety precautions are understood.
1
Safety Precautions For
Your Tower Fan
•
•
Do not use outdoors.
•
•
The fan must not be used if the guards are
damaged in any way.
Do not insert or allow foreign objects to enter
any ventilation or exhaust openings as this may
cause electric shock or fire, or damage to the
fan.
Do not run the cord of the fan under carpeting.
Do not cover the cord with throw rugs, runners
or other floor coverings. Arrange the cord away
from traffic areas so that it will not be tripped
over.
•
•
Do not use this fan in the immediate surrounds
of a bath, shower, laundry area or swimming
pool.
Be sure the fan is placed on a dry, even
surface. Do not use on soft surfaces, such as
beds, where opening may become blocked.
Keep your fan away from heat sources,
corrosive gases and avoid direct sunlight.
This fan is only to be used with the base fitted
and in good condition.
Disconnect the power plug before dismantling,
assembling or before cleaning.
Always unplug the fan when not in use for any
long length of time.
•
Never insert fingers, pencils or any other
objects through the guards whenever the power
plug is connected, especially while running.
•
•
Avoid touching mobile parts of the fan.
Do not attempt to move your fan whilst it is
operating. If your fan needs to be moved,
please ensure that it is turned off and you use
the carry handle on top of the tower.
When scrapping the fan at the end of its useful
life, follow local regulations.
•
•
•
•
•
Important Instructions - Retain For
Future Use
If you have any concerns regarding the performance and use of your appliance,
Ensure the above safety precautions are understood.
2
Locating Your Tower Fan
1.Always locate your fan on a flat level surface.
2.Your tower fan should be located in a dry,
cool, well ventilated location. Keep your fan
away from heat sources, corrosive gases and
avoid direct sunlight.
3.Do not attempt to move your tower fan
whilst it is operating. If your fan needs to be
moved, please ensure that it is turned off
and you use the carry handle at the rear of
the fan.
3
Features Of Your Sunbeam
Tower Fan
Remote control storage
When not in use, store your remote control in the handy
storage compartment on the rear of the fan body.
Carry handle
Convenient carry handle allows you to easily carry your fan
from room to room.
Power button
Simply press the power button to turn the unit on.
Control panel
The easy to read control panel allows you to quickly
see what functions have been selected on your tower
fan.
4
Remote control
Adjust the fan setting, auto off or oscillation
from anywhere in the room using the full
function remote control.
Auto Off button
Fan speed button
The auto off timer allows
you to set your tower fan to
turn off after either 1, 2, 4
or 8 hours.
Choose from 3 speed
settings, low medium
or high.
Nature and Sleep mode
Oscillation
When used in nature mode, the fan speed
is randomly adjusted, giving the feeling of
a natural breeze.
Your tower fan oscillates 70°,
distributing cool air throughout
the room.
Sleep mode is designed to be used when
retiring to bed; the fan speed is gradually
decreased until the unit is operating on
low speed, and when used in conjunction
with the auto off timer, will ultimately
switch the unit off.
5
Assembling Your Tower Fan
Remove the screws from beneath the tower
Join the two halves of the base together
1.Using a phillips head screwdriver, remove the
4 screws from underneath the tower.
1.Feed the cord between the two halves of the
base.
2.Put the screws aside. You will need them to
secure the base.
2.Clip the two halves of the base together,
ensuring the cord remains within the channel
formed when the two halves come together.
6
Assembling Your Tower Fan (continued)
Lower the tower onto the base
Screw the tower to the base
1.Align the tower and the base as shown.
2.Push the tower down onto the base until it is
1.Use the 4 screws you put aside earlier to
secure the tower to the base.
firmly held into position.
2.Clip the power cord into the semi circular
slot at the edge of the base. Ensure that the
cord fits neatly into the channel.
3.Stand the fan upright. It is now ready for
use.
7
Using Your Tower Fan
Switching the fan on
Selecting a fan speed setting
1.Place the fan on a flat level surface.
2.Insert the plug into a 230/240V power outlet
and turn the power on.
Your Sunbeam tower fan has 3 speed settings
as follows:
•
•
•
low speed
medium speed “2” light illuminates
high speed “3” light illuminates
“1” light illuminates
3.Press the power button
.
4.Press the fan speed button
to select
To select a fan speed, simply press the fan
speed button on the tower or the remote.
low, medium or high depending on your
preference.
Each press of the button will increase the
fan speed and then return back to the lowest
speed again.
Switching the fan off
•
To switch the fan off, simply press the power
button
.
•
While the fan remains plugged in to the
power socket, the fan will remember your last
fan speed, oscillation and mode setting for
the next time you switch the fan on again.
•
If you will not be using the fan for a length of
time, it is advisable to turn the power off at
the wall socket and unplug the power cord.
8
Using Your Tower Fan (continued)
Using the remote control
Changing the batteries
1.Remove the remote control from its compart-
ment at the rear of the tower as shown.
1.Slide the rear cover off the remote control
unit.
2.Point the remote towards the control panel
on the front of the tower to operate.
2.Replace the spent batteries with 2 fresh AAA
batteries as shown.
3.Replace the rear cover.
9
Using Your Tower Fan (continued)
Using the oscillation function
Using the auto off timer
The 70 degree oscillation function can be
used on any setting.
The auto off timer automatically switches the
fan off after a preset number of hours.
1.Turn the unit on and select any fan speed.
To activate this feature, simply press the auto
2.Press the
button on the tower or the
off button
on the tower or on the remote
remote. The fan will begin to oscillate from
side to side.
To stop the fan from oscillating, simply
control unit.
1.Press the auto off button once to switch
the fan off after 1 hour. The light on the
tower corresponding to the
illuminate.
position will
press the
button once again.
2.Press the auto off button again to have the
fan switch after 2 hours. The light on the
tower corresponding to the
illuminate.
position will
3.Similarly, pressing the auto off button a 3rd
or 4th time will set the fan to switch after 4
or 8 hours respectively. The corresponding
light on the tower
accordingly.
or
will illuminate
To cancel the setting, keep pressing the auto
off button until it cycles past 8 hours and
returns to its normal setting. The auto off
timer will be deactivated, the timing light will
be off, and the fan will remain on until it is
switched off manually.
10
Using Your Tower Fan (continued)
Nature mode
Sleep mode
Nature mode provides an extra level of
comfort by simulating the natural rise and fall
of the wind over time. You can use this mode
on any fan speed setting.
To use Nature mode:
1.Choose a fan speed.
Sleep mode is identical to Nature mode with
the added advantage that the highest fan
speed gradually decreases over time. This
allows you to turn the fan on a high speed
setting last thing at night, knowing that by
the time you are asleep, the fan has switched
itself down to a slower speed.
2.Press the
the remote until the
button on either the tower or
light illuminates.
To use Sleep mode:
1.Choose a fan speed.
The fan will now vary its speed every few
seconds between the chosen fan speed, each
lower fan speed, and off. For example, if you
set the fan speed to 2 (medium), the actual
fan speed will alternate between 2, 1 and off.
2.Press the
the remote until the
button on either the tower or
light illuminates.
The fan will now operate in the same manner
as with Nature mode, except that after 30
minutes, the maximum speed will decrease.
Eventually in this mode, the fan switches
down to 1 (low) speed, which alternates
between 1 and off.
To cancel Nature mode, Press the
button
on either the tower or the remote until the
light is no longer illuminated.
To cancel Sleep mode, Press the
button
on either the tower or the remote until the
light is no longer illuminated.
11
Troubleshooting Guide
If your tower fan fails to operate check the
following:
If your remote control fails to operate check
the following:
•
Make sure the electrical outlet or circuit
breaker is working.
•
Ensure that you point the remote towards the
front of the fan.
•
Check for obstructions around the air intake
grill.
•
Check that the batteries are not worn.
Replace if necessary.
Care And Cleaning
Ensure that your fan is switched off and
disconnected from the power outlet before
cleaning.
•
Take care that excessive dust does not build
up in the air-intake and air-outlet grill, and
clean it occasionally using a dry brush or
vacuum cleaner.
Store the fan in a cool dry place when not in
use, in its original carton if possible.
•
Carefully wipe your fan using a clean cloth.
Do not use abrasive cleaners or brushes to
clean the appliance as these may scratch the
surface.
•
12
2 Year Replacement Guarantee
We are so confident of the quality of our product, should this
appliance develop any malfunction within 2 years of purchase
(3 Months commercial use) due to faulty materials
or manufacture, we will replace it for you absolutely free.
Should you experience any difficulties
with your appliance, please phone our
free call customer service line for advice
on 1300 881 861 in Australia, or 0800
786 232 in New Zealand.
Sunbeam Service Centres
Sunbeam has established a network of
authorised service centres throughout
Australia and New Zealand to provide
quick, convenient service for our
customers.
Alternatively, simply return the faulty
appliance to your place of purchase,
along with your purchase receipt.
Should your appliance require repair
or service, either during or after the
guarantee period, contact your nearest
service centre.
Your Sunbeam 2 Year Replacement
Guarantee naturally does not cover
misuse or negligent handling, and
excludes breakables such as glass or
ceramic items, and normal wear and tear.
For a complete list of Sunbeam’s
authorised service centres:
Australia
Similarly, your 2 Year Replacement
Guarantee does not cover damage to
household surfaces as a result of water
or other substances leaking from your
appliance, nor does it cover freight costs.
1300 881 861
New Zealand
0800 786 232
In Australia, this guarantee is additional
to the conditions and guarantees which
are mandatory as implied under the
Trade Practices Act 1974 and State and
Territory legislation.
13
Consumer Hotline
In Australia
Or call 1300 881 861
In New Zealand
Or call 0800 786 232
is a registered Trademark of Sunbeam.
Made in China.
Due to minor changes in design or otherwise,
the product may differ from the one shown in this leaflet.
© Copyright Sunbeam Corporation Limited 2008.
ABN 45 000 006 771
0708
Sunbeam Corporation is a division of GUD Holdings Ltd.
|